GE N60 Instruction Manual page 264

FLEXLOGIC
Operand type
RxGOOSE Boolean
Virtual Input
Virtual Output
The following table lists alphabetically the operands available for the relay.
Table 5-21: N60 FlexLogic operands
Operand type
CONTROL
PUSHBUTTONS
DIRECT DEVICES
DIRECT INPUT/
OUTPUT CHANNEL
MONITORING
5
ELEMENT:
Eight-bit comparator
ELEMENT:
Eight-bit switch
5-148
State Example of format
On RxGOOSE Boolean 1 On
On Virt Ip 1 On
On Virt Op 1 On
Operand syntax
CONTROL PUSHBTN 1 ON
CONTROL PUSHBTN 2 ON
CONTROL PUSHBTN 3 ON
CONTROL PUSHBTN 4 ON
CONTROL PUSHBTN 5 ON
CONTROL PUSHBTN 6 ON
CONTROL PUSHBTN 7 ON
DIRECT DEVICE 1On

DIRECT DEVICE 16On
DIRECT DEVICE 1Off

DIRECT DEVICE 16Off
DIR IO CH1 CRC ALARM
DIR IO CH2 CRC ALARM
DIR IO CH1 UNRET ALM
DIR IO CH2 UNRET ALM
8BIT COMP 1 PKP
8BIT COMP 1 DPO
8BIT COMP 1 OP
8BIT COMP 1 BIT 0
8BIT COMP 1 BIT 1
8BIT COMP 1 BIT 2
8BIT COMP 1 BIT 3
8BIT COMP 1 BIT 4
8BIT COMP 1 BIT 5
8BIT COMP 1 BIT 6
8BIT COMP 1 BIT 7
8BIT COMP 2 to 8BIT COMP 6
8BIT SWITCH 1 BIT 0
8BIT SWITCH 1 BIT 1
8BIT SWITCH 1 BIT 2
8BIT SWITCH 1 BIT 3
8BIT SWITCH 1 BIT 4
8BIT SWITCH 1 BIT 5
8BIT SWITCH 1 BIT 6
8BIT SWITCH 1 BIT 7
8BIT SWITCH 2 to 8BIT SWITCH 6
N60 NETWORK STABILITY AND SYNCHROPHASOR MEASUREMENT SYSTEM – INSTRUCTION MANUAL
Characteristics
[Input Is '1' (= ON) if...]
The RxGOOSE Boolean is presently in the ON state
The virtual input is presently in the ON state
The virtual output is presently in the set state (that is,
evaluation of the equation that produces this virtual output
results in a "1")
Operand description
Control pushbutton 1 is being pressed
Control pushbutton 2 is being pressed
Control pushbutton 3 is being pressed
Control pushbutton 4 is being pressed
Control pushbutton 5 is being pressed
Control pushbutton 6 is being pressed
Control pushbutton 7 is being pressed
Flag is set, logic=1

Flag is set, logic=1
Flag is set, logic=1

Flag is set, logic=1
The rate of direct input messages received on channel 1 and failing the CRC
exceeded the user-specified level.
The rate of direct input messages received on channel 2 and failing the CRC
exceeded the user-specified level.
The rate of returned direct input/output messages on channel 1 exceeded
the user-specified level (ring configurations only).
The rate of returned direct input/output messages on channel 2 exceeded
the user-specified level (ring configurations only).
Comparator 1 has picked up
Comparator 1 has dropped out
Comparator 1 has operated
Bit 0 of comparator 1 asserted (the least significant bit)
Bit 1 of comparator 1 asserted
Bit 2 of comparator 1 asserted
Bit 3 of comparator 1 asserted
Bit 4 of comparator 1 asserted
Bit 5 of comparator 1 asserted
Bit 6 of comparator 1 asserted (the most significant bit)
Sign bit of comparator 1 asserted (asserted for negative values; de-asserted
for positive values)
Same set of operands as shown for 8 BIT COMP 1
Bit 0 of eight-bit switch 1 asserted (the least significant bit)
Bit 1 of eight-bit switch 1 asserted
Bit 2 of eight-bit switch 1 asserted
Bit 3 of eight-bit switch 1 asserted
Bit 4 of eight-bit switch 1 asserted
Bit 5 of eight-bit switch 1 asserted
Bit 6 of eight-bit switch 1 asserted
Bit 7 of eight-bit switch 1 asserted (the most significant bit)
Same set of operands as shown for 8 BIT SWITCH 1
CHAPTER 5: SETTINGS