Maintenance Trig - ABB ACS350 User Manual

Parameters – complete descriptions
Index Name/Selection
2613 USER DEFINED F2
0.0...500.0 Hz
2614 USER DEFINED U3
0...120% of U V
N
2615 USER DEFINED F3
0.0...500.0 Hz
2616 USER DEFINED U4
0...120% of U V
N
2617 USER DEFINED F4
0.0...500.0 Hz
2618 FW VOLTAGE
0...120% of U V
N
29 MAINTENANCE
TRIG
2901 COOLING FAN TRIG
0.0...6553.5 kh
2902 COOLING FAN ACT
0.0...6553.5 kh
2903 REVOLUTION TRIG
0...65535 Mrev
2904 REVOLUTION ACT
0...65535 Mrev
2905 RUN TIME TRIG
0.0...6553.5 kh
2906 RUN TIME ACT
0.0...6553.5 kh
Description
Defines the second frequency point of the custom U/f curve.
Frequency
Defines the third voltage point of the custom U/f curve at the frequency
defined by parameter 2615
ratio on page 112.
Voltage
Defines the third frequency point of the custom U/f curve.
Frequency
Defines the fourth voltage point of the custom U/f curve at the frequency
defined by parameter 2617
ratio on page 112.
Voltage
Defines the fourth frequency point of the custom U/f curve.
Frequency
Defines the voltage of the U/f curve when frequency is equal to or exceeds
the motor nominal frequency
Custom U/f ratio on page 112.
Voltage
Maintenance triggers
Defines the trigger point for the drive cooling fan run time counter. Value is
compared to parameter 2902
Time. If parameter value is set to zero, the trigger is disabled.
Defines the actual value for the cooling fan run time counter. When
parameter 2901 COOLING FAN TRIG has been set to a non zero value, the
counter starts. When the actual value of the counter exceeds the value
defined by parameter 2901, a maintenance notice is displayed on the panel.
Time. Parameter is reset by setting it to zero.
Defines the trigger point for the motor revolution counter. Value is compared
to parameter 2904 REVOLUTION ACT value.
Millions of revolutions. If parameter value is set to zero, the trigger is
disabled.
Defines the actual value for the motor revolution counter. When parameter
2903 REVOLUTION TRIG has been set to a non zero value, the counter
starts. When the actual value of the counter exceeds the value defined by
parameter 2903, a maintenance notice is displayed on the panel.
Millions of revolutions. Parameter is reset by setting it to zero.
Defines the trigger point for the drive run time counter. Value is compared to
parameter 2906 RUN TIME ACT value.
Time. If parameter value is set to zero, the trigger is disabled.
Defines the actual value for the drive run time counter. When parameter
RUN TIME TRIG has been set to a non zero value, the counter starts. When
the actual value of the counter exceeds the value defined by parameter 2905,
a maintenance notice is displayed on the panel.
Time. Parameter is reset by setting it to zero.
USER DEFINED F3. See section
USER DEFINED F4. See section
(9907 MOTOR NOM FREQ). See section
COOLING FAN ACT value.
Def, FbEq
20
1 = 0.1 Hz
47.5% of U
Custom U/f
1 = 1 V
25
1 = 0.1 Hz
76% of U
Custom U/f
1 = 1 V
40
1 = 0.1 Hz
95% of U
1 = 1 V
0
1 = 0.1 kh
0
1 = 0.1 kh
0
1 = 1 Mrev
0
1 = 1 Mrev
0
1 = 0.1 kh
2905 0
1 = 0.1 kh
Actual signals and parameters
195
N
N
N