ABB ACS350 User Manual page 150

150
Parameters – short form list
Index Name/Selection
20 LIMITS
2001 MINIMUM SPEED
2002 MAXIMUM SPEED
2003 MAX CURRENT
2005 OVERVOLT CTRL
2006 UNDERVOLT CTRL
2007 MINIMUM FREQ
2008 MAXIMUM FREQ
2013 MIN TORQUE SEL
2014 MAX TORQUE SEL
2015 MIN TORQUE 1
2016 MIN TORQUE 2
2017 MAX TORQUE 1
2018 MAX TORQUE 2
2019 BRAKE CHOPPER
2020 BRAKE CHOPPER
21 START/STOP
2101 START FUNCTION
2102 STOP FUNCTION
2103 DC MAGN TIME
2104 DC HOLD CTL
2105 DC HOLD SPEED
2106 DC CURR REF
2107 DC BRAKE TIME
2108 START INHIBIT
2109 EMER STOP SEL
2110 TORQ BOOST CURR
2111 STOP SIGNAL DLY
2112 ZERO SPEED DELAY
22 ACCEL/DECEL
2201 ACC/DEC 1/2 SEL
2202 ACCELER TIME 1
2203 DECELER TIME 1
2204 RAMP SHAPE 1
2205 ACCELER TIME 2
2206 DECELER TIME 2
2207 RAMP SHAPE 2
2208 EMER DEC TIME
2209 RAMP INPUT 0
23 SPEED CONTROL
2301 PROP GAIN
2302 INTEGRATION TIME
2303 DERIVATION TIME
2304 ACC COMPENSATION Defines the derivation time for acceleration/(deceleration)
2305 AUTOTUNE RUN
Actual signals and parameters
Description
Drive operation limits.
Defines the allowed minimum speed.
Defines the allowed maximum speed.
Defines the allowed maximum motor current.
Activates or deactivates the overvoltage control of the
intermediate DC link.
Activates or deactivates the undervoltage control of the
intermediate DC link.
Defines the minimum limit for the drive output frequency.
Defines the maximum limit for the drive output frequency.
Selects the minimum torque limit for the drive.
Selects the maximum torque limit for the drive.
Defines minimum torque limit 1 for the drive.
Defines minimum torque limit 2 for the drive.
Defines maximum torque limit 1 for the drive.
Defines maximum torque limit 2 for the drive.
Phased out parameter in sw version 2.51b and later.
Selects the brake chopper control.
Start and stop modes of the motor
Selects the motor starting method.
Selects the motor stop function.
Defines the pre-magnetising time.
Activates the DC Hold or DC braking function.
Defines the DC hold speed.
Defines the DC hold current.
Defines the DC brake time.
Enables the start inhibit function.
Selects the source for the external emergency stop command.
Defines the maximum supplied current during torque boost.
Defines the stop signal delay time when parameter 2102 STOP
FUNCTION is set to SPEED COMP.
Defines the delay for the Zero Speed Delay function.
Acceleration and deceleration times
Defines the source from which the drive reads the signal that
selects between the two ramp pairs.
Defines the acceleration time 1.
Defines the deceleration time 1.
Selects the shape of the acceleration/deceleration ramp 1.
Defines the acceleration time 2.
Defines the deceleration time 2.
Selects the shape of the acceleration/deceleration ramp 2.
Defines the time within the drive is stopped if an emergency stop
is activated.
Defines the source for forcing the ramp input to zero.
Speed controller variables.
Defines a relative gain for the speed controller.
Defines an integration time for the speed controller.
Defines the derivation time for the speed controller.
compensation.
Start automatic tuning of the speed controller.
Def Custom
0
Eur: 1500 / US:
1800
1.8 ² I2N
ENABLE
ENABLE(TIME)
0
Eur: 50 / US: 60
MIN TORQUE 1
MAX TORQUE 1
-300
-300
300
300
INBUILT
AUTO
COAST
0.3
NOT SEL
5
30
0
OFF
NOT SEL
100
0
0
DI5
5
5
0
60
60
0
1
NOT SEL
10
39204
0
0
OFF