ABB ACS350 User Manual page 157

Parameters – short form list
Index Name/Selection
5127 FBA PAR REFRESH
52 PANEL COMM
5201 STATION ID
5202 BAUD RATE
5203 PARITY
5204 OK MESSAGES
5205 PARITY ERRORS
5206 FRAME ERRORS
5207 BUFFER OVERRUNS
5208 CRC ERRORS
53 EFB PROTOCOL
5302 EFB STATION ID
5303 EFB BAUD RATE
5304 EFB PARITY
5305 EFB CTRL PROFILE
5306 EFB OK MESSAGES
5307 EFB CRC ERRORS
5310 EFB PAR 10
5311 EFB PAR 11
5312 EFB PAR 12
5313 EFB PAR 13
5314 EFB PAR 14
5315 EFB PAR 15
5316 EFB PAR 16
5317 EFB PAR 17
5318 EFB PAR 18
5319 EFB PAR 19
5320 EFB PAR 20
54 FBA DATA IN
5401 FBA DATA IN 1
5402 FBA DATA IN 2
.... ...
5410 FBA DATA IN 10
55 FBA DATA OUT
5501 FBA DATA OUT 1
5502 FBA DATA OUT 2
... ...
5510 FBA DATA OUT 10
84 SEQUENCE PROG
8401 SEQ PROG ENABLE
8402 SEQ PROG START
Description
Validates any changed adapter module configuration parameter
settings.
Communication settings for the control panel port on the drive
Defines the address of the drive.
Defines the transfer rate of the link.
Defines the use of parity and stop bit(s).
Number of valid messages received by the drive.
Number of characters with a parity error received from the
Modbus link.
Number of characters with a framing error received by the
Modbus link.
Number of characters which overflow the buffer, i.e. number of
characters which exceed the maximum message length, 128
bytes.
Number of messages with an CRC (cyclic redundancy check)
error received by the drive.
Embedded fieldbus link settings.
Defines the address of the device.
Defines the transfer rate of the link.
Defines the use of parity and stop bit(s) and the data length.
Selects the communication profile.
Number of valid messages received by the drive.
Number of messages with an CRC (cyclic redundancy check)
error received by the drive.
Selects an actual value to be mapped to Modbus register 40005.
Selects an actual value to be mapped to Modbus register 40006.
Selects an actual value to be mapped to Modbus register 40007.
Selects an actual value to be mapped to Modbus register 40008.
Selects an actual value to be mapped to Modbus register 40009.
Selects an actual value to be mapped to Modbus register 40010.
Selects an actual value to be mapped to Modbus register 40011.
Selects an actual value to be mapped to Modbus register 40012.
Reserved
ABB Drives profile (ABB DRV LIM or ABB DRV FULL) Control
Word. Read only copy of the Fieldbus Control Word.
ABB Drives profile (ABB DRV LIM or ABB DRV FULL) Status
Word. Read only copy of the Fieldbus Status Word.
Data from drive to fieldbus controlle.
Selects data to be transferred from the drive to the fieldbus
controller.
See 5401 FBA DATA IN 1.
...
See 5401 FBA DATA IN 1.
Data from fieldbus controller to drive.
Selects data to be transferred from the fieldbus controller to the
drive.
See 5501 FBA DATA OUT 1.
...
See 5501 FBA DATA OUT 1.
Sequence programming.
Enables sequence programming.
Selects the source for the sequence programming activation
signal.
Def Custom
1
39242
8 NONE 1
0
0
0
0
0
1
39242
8 NONE 1
ABB DRV LIM
0
0
0
0
0
0
0
0
0
0
0
0x0000
0x0000
DISABLED
NOT SEL
Actual signals and parameters
157