ABB ACS560 Firmware Manual page 158

158
Parameter
10.24 RO1 source
10.27 RO2 source
10.30 RO3 source
12.20 AI1 scaled at AI1
max
12.30 AI2 scaled at AI2
max
13.12 AO1 source
13.18 AO1 source max
19.11 Ext1/Ext2 selection
19.14 Ext2 control mode
19.17 Local control mode
20.01 Ext1 commands
20.03 Ext1 in1 source
20.04 Ext1 in2 source
20.05 Ext1 in3 source
20.06 Ext2 commands
20.08 Ext2 in1 source
20.09 Ext2 in2 source
20.12 Run enable 1
source
21.03 Stop mode
22.11 Ext1 speed ref1
22.18 Ext2 speed ref1
22.21 Constant speed
function
22.22 Constant speed sel1
22.23 Constant speed sel2
22.24 Constant speed sel3
22.26 Constant speed 1
22.27 Constant speed 2
96.04 Macro select
PFC (16) SPFC
7 = Running 7 = Running
15 = Fault (-1) 43 = PFC1
46 = PFC2 46 = PFC2
50.000 50.000
50.000 50.000
2 = Output 2 = Output
frequency frequency
50.0 50.0
1 = DI3 5 = DI3
2 = Speed 2 = Speed
0 = No 0 = No
1 = In1 Start 1 = In1 Start
2 = DI1 2 = DI1
0 = Always off 0 = Always off
0 = Always off 0 = Always off
1 = In1 Start 1 = In1 Start
7 = DI6 7 = DI6
0 = Always off 0 = Always off
3 = DI2 3 = DI2
0 = Coast 0 = Coast
1 = AI1 scaled 1 = AI1 scaled
16 = PID 0 = Zero
0b0001 0b0001
0 = Always off 4 = DI3
0 = Always off 5 = DI4
0 = Always off 0 = Always off
300.00 300.00
600.00 600.00
Plastic Extrusion
(18)
(20)
11 = Zero speed
7 = Running
14 = Fault
1500.000
50.000
1 = Motor speed
used
1500.0
0 = EXT1
2 = Speed
1 = Yes
1 = In1 Start
2 = DI1
3 = DI2
0 = Always off
0 = Always off
0 = Always off
0 = Always off
1 = Selected
1 = Ramp
1 = AI1 scaled
0 = Zero
0b0001
4 = DI3
5 = DI4
0 = Always off
300.00
600.00
Jigar (30)
11 = Ready run
7 = Running
14 = Fault (-1)
1500.000
100.000
1 = Output
frequency
50.0
0 = DI3
2 = Torque
1 = No
1 = In1 Start fwd;
In2 Start rev
2 = DI1
3 = DI2
0 = Always off
0 = In1 Start
0 = DI1
0 = Always off
1 = Selected
1 = Coast
1 = AI1 scaled
0 = Zero
0b0001
4 = Always off
5 = Always off
0 = Always off
300.00
600.00