Parameter Default Values For Different Application Macros - ABB ACS560 Firmware Manual

154

Parameter default values for different application macros

The default values listed in the
standard macro (factory macro). The default values may differ for other macros. The
different default values for each application macros are listed in the below table.
Parameter
10.24 RO1 source
10.27 RO2 source
10.30 RO3 source
12.20 AI1 scaled at AI1
max
12.30 AI2 scaled at AI2
min
13.12 AO1 source
13.18 AO1 source max
19.11 Ext1/Ext2
selection
19.14 Ext2 control
mode
20.01 Ext1 commands
20.03 Ext1 in1 source
20.04 Ext1 in2 source
20.05 Ext1 in3 source
20.06 Ext2 commands
20.08 Ext2 in1 source
20.09 Ext2 in2 source
20.12 Run enable 1
source
21.03 Stop mode
22.11 Ext1 speed ref1
22.18 Ext2 speed ref1
22.21 Constant speed
function
22.22 Constant speed
sel1
22.23 Constant speed
sel2
22.24 Constant speed
sel3
Parameters
ABB standard ABB standard
(1) (vector)
2 = Ready run 2 = Ready run
7 = Running 7 = Running
15 = Fault (-1) 15 =
50.000 1500.000
50.000 1500.000
2 = Output 1 = Motor speed
frequency used
50.0 1500.0
0 = EXT1 0 = EXT1
2 = Speed 2 = Speed
2 = In1 Start; In2 2 = In1 Start; In2 Dir
Dir
2 = DI1 2 = DI1
3 = DI2 3 = DI2
0 = Always off 0 = Always off
0 = Not selected 0 = Not selected
0 = Always off 0 = Always off
0 = Always off 0 = Always off
1 = Selected 1 = Selected
1 = Coast 1 = Coast
1 = AI1 scaled 1 = AI1 scaled
0 = Zero 0 = Zero
0b0001 0b0001
4 = DI3 4 = DI3
5 = DI4 5 = DI4
0 = Always off 0 = Always off
table on page 161
96.04 Macro select
Torque control
(17)
2 = Ready run
7 = Running
Fault (-1) 15 = Fault (-1)
1500.000
100.000
1 = Motor speed
used
1500.0
5 = DI3
3 = Torque
2 = In1 Start; In2
Dir
2 = DI1
3 = DI2
0 = Always off
1 = In1 Start
2 = DI1
3 = DI2
7 = DI6
1 = Coast
1 = AI1 scaled
0 = Zero
0b0000
5 = DI4
5 = DI4
0 = Always off
are applicable for ABB
3-wire
(26)
(11)
2 = Ready run
7 = Running
15 = Fault (-1)
50.000
50.000
2 = Output
frequency
50.0
0 = EXT1
2 = Speed
2 = In1P Start; In2
Stop; In3 Dir
2 = DI1
3 = DI2
0 = Always off
1 = In1 Start
2 = DI1
3 = DI2
4 = DI3
1 = Coast
1 = AI1 scaled
0 = Zero
5 = DI4
6 = DI5
0 = Always off