Mitsubishi Electric Melsec-F FX3GC Series User Manual page 193

FX /FX /FX /FX /FX
3S 3G 3GC 3U 3UC
Built-in Positioning Functions
10.4 Important Points
• During pulse output operation, if the output pulse frequency
the speed and then stop the pulse outputting operation if the acceleration/deceleration function is ON.
However, if the acceleration/deceleration function is not activated, the PLC will immediately stop the pulse
outputting operation.
Before outputting pulses again, check that the "pulse output monitor" (BUSY/READY) flag is off, and then
wait until 1 or more cycles of operation have been completed. After that, set (change) the output pulse
frequency to a value other than "K0".
• During pulse outputting operation, do not change the sign attached to the output pulse frequency
value .
S
If it is necessary to change the sign, stop the servo motor first by setting the output pulse frequency value
to "K0", and wait for the motor to stop completely after decelerating to stop. And then, change the
S
sign attached to the output pulse frequency value
If the sign attached to the output pulse frequency value
operation, the operation may be changed as follows, and the machine, therefore, may be damaged:
1) The pulse outputting operation may be stopped.
2) "Pulse output monitor" (BUSY/READY) flag may be turned off.
(The pulse outputting operation may be stopped, but the motor may not be stopped immediately.)
3) Operation may be performed in the specified direction at the frequency specified by the output
pulse frequency value
• If the instruction activation contact is turned off during pulse outputting operation while the acceleration/
deceleration function is ON, the speed will decelerate and the operation will stop.
If the instruction activation contact is turned off during pulse outputting operation while the acceleration/
deceleration function is OFF, the operation will stop immediately.
The "Instruction execution complete" flag (M8029) will not turn on.
• If a limit flag (forward rotation or reverse rotation) in the operation direction is turned ON, the speed will
decelerate and the operation will stop in the case that the acceleration/deceleration function is ON, or the
operation will stop immediately in the case that the acceleration/deceleration function is OFF. In this case,
the "Instruction execution abnormal end" flag (M8329) will turn on when execution of the instruction is
complete.
For details on the "Instruction execution abnormal end" flag, refer to Subsection 4.7.4.
• If the "pulse output monitor" (BUSY/READY) flag is on, a positioning instruction (including PLSR and
PLSY) that uses the same output cannot be executed.
If the "pulse output monitor" (BUSY/READY) flag is still on after the instruction activation contact is turned
off, do not execute a positioning instruction (including PLSR and PLSY instructions) that uses the same
output number.
• After executing the instruction, the rotation direction signal output will turn off.
1.
Important items for FX
• Acceleration/deceleration will not be performed when starting or stopping the operation. For this reason, if
it is necessary to use the cushion start function or the cushion stop function, increase/decrease the output
pulse frequency value
2.
Important items for FX
• If acceleration/deceleration is enabled, the variable speed pulse output (PLSV) instructions for all of the
pulse output destination devices will use acceleration/deceleration. This means that acceleration/
deceleration cannot be specified separately for each pulse output destination device.
PLC User's Manual - Positioning Control Edition
.
S
PLCs below Ver. 2.20
3UC
using the FNC 67 (RAMP) instruction, etc.
S
PLC Ver. 2.20 or later and FX
3UC
10 Variable Speed Operation (Variable Speed Pulse Output) - PLSV Instruction
For important programming points, refer to Section 4.7.
is changed to "K0", the PLC will reduce
S
.
S
is changed during pulse outputting
S
/FX /FX
3S 3G 3GC
10.4 Important Points
/FX PLC
3U
B - 149
A
B
Apx.