Mitsubishi Electric 800 Series Instruction Manual page 131

Parameter List
Parameter list (by function group)
Pr.
Pr.
group
G108 1299
Second pre-excitation selection
G110 12
DC injection brake operation voltage
Regeneration avoidance operation
G120 882
selection
G121 883
Regeneration avoidance operation level
Regeneration avoidance at deceleration
G122 884
detection sensitivity
Regeneration avoidance compensation
G123 885
frequency limit value
G124 886
Regeneration avoidance voltage gain
G125 665
Regeneration avoidance frequency gain
Increased magnetic excitation
G130 660
deceleration operation selection
G131 661
Magnetic excitation increase rate
Increased magnetic excitation current
G132 662
level
G200 800
Control method selection
G201 85
Excitation current refraction point
Excitation current low speed
G202 86
multiplying factor
G203 245
Rated slip
G204 246
Slip compensation time constant
Constant-power range slip
G205 247
compensation selection
Constant output range speed control P
G206 1116
gain compensation
Constant output range torque
G210 803
characteristic selection
G211 820
Speed control P gain 1
G212 821
Speed control integral time 1
Torque control P gain 1 (current loop
G213 824
proportional gain)
Torque control integral time 1 (current
G214 825
loop integral time)
G215 823

Speed detection filter 1
G216 827
Torque detection filter 1
G217 854
Excitation ratio
G218 1115
Speed control integral term clear time
Speed feed forward control/model
G220 877
adaptive speed control selection
G221 878
Speed feed forward filter
G222 879
Speed feed forward torque limit
G223 881
Speed feed forward gain
G224 828
Model speed control gain
G230 840
Torque bias selection
G231 841
Torque bias 1
G232 842
Torque bias 2
G233 843
Torque bias 3
G234 844
Torque bias filter
G235 845
Torque bias operation time
G236 846
Torque bias balance compensation
G237 847
Fall-time torque bias terminal 1 bias
G238 848
Fall-time torque bias terminal 1 gain
G240 367

Speed feedback range
G241 368

Feedback gain
Per-unit speed control reference
G260 1121
frequency
G261 1117
Speed control P gain 1 (per-unit system)
Model speed control gain (per-unit
G262 1119
system)
G263 1348
P/PI control switchover frequency
G264 1349
Emergency stop operation selection
G300 451
Second motor control method selection
Second motor excitation current
G301 565
refraction point
130
PARAMETERS
Refer
Name
to page
599
599
614
614
614
614
614
614
617
617
617
137
595
595
618
618
618
164
154,
190
164
164
201,
240
201,
240
239
239
240
164
173,
236
173
173
173
173,
236
175
175
175
175
175
175
175
175
175
619
619
164
164
173
164
269
137
595
Pr.
Pr.
group
Second motor excitation current low
G302 566
speed scaling factor
G311 830
Speed control P gain 2
G312 831
Speed control integral time 2
G313 834
Torque control P gain 2
G314 835
Torque control integral time 2
G315 833

Speed detection filter 2
G316 837
Torque detection filter 2
G361 1118
Speed control P gain 2 (per-unit system)
G400 286
Droop gain
G401 287
Droop filter time constant
G402 288
Droop function activation selection
G403 994
Droop break point gain
G404 995
Droop break point torque
G410 653
Speed smoothing control
G411 654
Speed smoothing cutoff frequency
G420 679
Second droop gain
G421 680
Second droop filter time constant
Second droop function activation
G422 681
selection
G423 682
Second droop break point gain
G424 683
Second droop break point torque
G601 1003
Notch filter frequency
G602 1004
Notch filter depth
G603 1005
Notch filter width
Speed control gain (Advanced magnetic
G932 89
flux vector)
G942 569
Second motor speed control gain

The setting is available when a plug-in option for Vector control is installed.

Setting can be made only for the standard model.

The setting is available when the PLC function is enabled.
Refer
Name
to page
595
164
164
201
201
239
239
164
621
621
621
621
621
624
624
621
621
621
621
621
181
181
181
143
143