Mitsubishi Electric 800 Series Instruction Manual page 128

Pr.
Pr.
group
A512 361

Position shift
A520 362

Orientation position loop gain
A521 363

Completion signal output delay time
A522 364

Encoder stop check time
A523 365

Orientation limit
A524 366

Recheck time
A525 393

Orientation selection
A526 351

Orientation speed
A527 352

Creep speed
A528 353

Creep switchover position
A529 354

Position loop switchover position
A530 355

DC injection brake start position
A531 356

Internal stop position command
A532 357

Orientation in-position zone
A533 358

Servo torque selection
A540 394

Number of machine side gear teeth
A541 395

Number of motor side gear teeth
A542 396

Orientation speed gain (P term)
A543 397

Orientation speed integral time
A544 398

Orientation speed gain (D term)
A545 399

Orientation deceleration ratio
A546 829

Number of machine end encoder pulses
A600 759
PID unit selection
A601 131
PID upper limit
A602 132
PID lower limit
A603 553
PID deviation limit
A604 554
PID signal operation selection
A605 1134
PID upper limit manipulated value
A606 1135
PID lower limit manipulated value
Integral stop selection at limited
A607 1015
frequency
A610 128
PID action selection
A611 133
PID action set point
PID control automatic switchover
A612 127
frequency
A613 129
PID proportional band
A614 130
PID integral time
A615 134
PID differential time
A616 760
Pre-charge fault selection
A617 761
Pre-charge ending level
A618 762
Pre-charge ending time
A619 763
Pre-charge upper detection level
A620 764
Pre-charge time limit
A621 575
Output interruption detection time
A622 576
Output interruption detection level
A623 577
Output interruption cancel level
A624 609
PID set point/deviation input selection
A625 610
PID measured value input selection
A630 934
PID display bias coefficient
A631 934
PID display bias analog value
A632 935
PID display gain coefficient
A633 935
PID display gain analog value
A640 1142
Second PID unit selection
A641 1143
Second PID upper limit
Refer
Name
to page
473
473
473
473
473
473
473
473
473
473
473
473
473
473
473
473
473
473
473
473
473
473
501
488,
508
488,
508
488
488
508
508
488
488,
508
488,
508
488
488,
508
488,
508
488,
508
504
504
504
504
504
488
488
488
488,
508
488,
508
Simple Simple Simple 501
501
Simple Simple Simple
501
Simple Simple Simple
501
Simple Simple Simple
488
488
Parameter list (by function group)
Pr.
Pr.
group
A642 1144
Second PID lower limit
A643 1145
Second PID deviation limit
A644 1146
Second PID signal operation selection
A650 753
Second PID action selection
A651 755
Second PID action set point
Second PID control automatic
A652 754
switchover frequency
A653 756
Second PID proportional band
A654 757
Second PID integral time
A655 758
Second PID differential time
A656 765
Second pre-charge fault selection
A657 766
Second pre-charge ending level
A658 767
Second pre-charge ending time
Second pre-charge upper detection
A659 768
level
A660 769
Second pre-charge time limit
Second output interruption detection
A661 1147
time
Second output interruption detection
A662 1148
level
A663 1149
Second output interruption cancel level
Second PID set point/deviation input
A664 1140
selection
Second PID measured value input
A665 1141
selection
Second PID display bias coefficient
A670 1136
Simple Simple Simple
Second PID display bias analog value
A671 1137
Simple Simple Simple
Second PID display gain coefficient
A672 1138
Simple Simple Simple
Second PID display gain analog value
A673 1139
Simple Simple Simple
A680 573
4 mA input check selection
A681 777
4 mA input fault operation frequency
A682 778
4 mA input check filter
Automatic restart after instantaneous
A700 162
power failure selection
Rotation direction detection selection at
A701 299
restarting
A702 57
Restart coasting time
A703 58
Restart cushion time
A704 163
First cushion time for restart
A705 164
First cushion voltage for restart
Stall prevention operation level for
A710 165
restart
A711 298
Frequency search gain
A712 560
Second frequency search gain
A730 261
Power failure stop selection
Subtracted frequency at deceleration
A731 262
start
A732 263
Subtraction starting frequency
A733 264
Power-failure deceleration time 1
A734 265
Power-failure deceleration time 2
Power failure deceleration time
A735 266
switchover frequency
A785 294
UV avoidance voltage gain
A786 668
Power failure stop frequency gain
A800 414
PLC function operation selection
A801 415
Inverter operation lock mode setting
A802 416
Pre-scale function selection
A803 417
Pre-scale setting value
A804 498
PLC function flash memory clear
Parameter List
Refer
Name
to page
488
488
488
488
488
488
488
488
488
504
504
504
504
504
488
488
488
488
488
501
501
501
501
411
411
411
515,
522
515
515
515
515
515
515
426,
522
426,
522
526
526
526
526
526
526
526
526
531
531
531
531
531
127
PARAMETERS
5