Cisco Codec C20 Reference Manual page 61

Cisco TelePresence System Codec C20
Contents Introduction
xConfiguration Video SelfviewDefault Mode
Determine if the main video source (self view) shall be displayed on screen after a call. The position
and size of the self view window is determined by the Video SelfviewDefault PIPPosition and the Video
Selfview FullscreenMode settings respectively.
This setting obsoletes the Video Selfview setting as from TC6.0.
Requires user role: ADMIN
Value space: <Off/Current/On>
Off: Self view is switched off when leaving a call.
Current: Self view is left as is, i.e. if it was on during the call, it remains on after the call; if it was
off during the call, it remains off after the call.
On: Self view is switched on when leaving a call.
example: xConfiguration Video SelfviewDefault Mode: Current
xConfiguration Video SelfviewDefault FullscreenMode
Determine if the main video source (self view) shall be shown in full screen or as a small picture-in-
picture (PiP) after a call. The setting only takes effect when self view is switched on (see the Video
SelfviewDefault Mode setting).
Requires user role: ADMIN
Value space: <Off/Current/On>
Off: Self view will be shown as a PiP.
Current: The size of the self view picture will be kept unchanged when leaving a call, i.e. if it was
a PiP during the call, it remains a PiP after the call; if it was fullscreen during the call, it remains
fullscreen after the call.
On: The self view picture will be shown in fullscreen.
example: xConfiguration Video SelfviewDefault FullscreenMode: Current
Codec C20 API Reference Guide TC6.0 February 2013.
D14869.05
About the API xConfiguration xConfiguration
61
xCommand
xConfiguration Video SelfviewDefault PIPPosition
Determine the position on screen of the small self view picture-in-picture (PiP) after a call. The setting
only takes effect when self view is switched on (see the Video SelfviewDefault Mode setting) and
fullscreen view is switched off (see the Video SelfviewDefault FullscreenMode setting).
This setting obsoletes the Video SelfviewPosition setting as from TC6.0.
Requires user role: ADMIN
Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/
LowerLeft/LowerRight >
Current: The position of the self view PiP will be kept unchanged when leaving a call.
UpperLeft: The self view PiP will appear in the upper left corner of the screen.
UpperCenter: The self view PiP will appear in the upper center position.
UpperRight: The self view PiP will appear in the upper right corner of the screen.
CenterLeft: The self view PiP will appear in the center left position.
CentreRight: The self view PiP will appear in the center right position.
LowerLeft: The self view PiP will appear in the lower left corner of the screen.
LowerRight: The self view PiP will appear in the lower right corner of the screen.
example: xConfiguration Video SelfviewDefault PIPPosition: Current
xConfiguration Video SelfviewDefault OnMonitorRole
Determine which monitor/output to display the main video source (self view) on after a call. The value
reflects the monitor roles set for the different outputs in the Video Output HDMI MonitorRole settings.
The setting applies both when self view is displayed in full screen, and when it is displayed as picture-
in-picture (PiP), but only if the Video Monitors setting is set to Dual.
Requires user role: ADMIN
Value space: <First/Second/Current>
First: The self view picture will be shown on outputs with the Video Output HDMI MonitorRole set
to First.
Second: The self view picture will be shown on outputs with the Video Output HDMI MonitorRole
set to Second.
Current: When leaving the call, the self view picture will be kept on the same output as during the call.
example: xConfiguration Video SelfviewDefault OnMonitorRole: Current
API Reference Guide
xStatus Appendices
Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved.