Mitsubishi Electric MELSOFT FR Configurator2 Instruction Manual page 68

Condition
Operation
(Pr. 551
location
setting)
Run command
(start, stop)
3 (USB
Running
connector)
frequency
9999
setting
(automatic
Monitor
recognition,
with USB
Parameter write ○
connection)
Parameter read ○
Inverter reset
USB
connector
Run command
(start, stop)
Running
frequency
Other than
setting
the above
Monitor
Parameter write ×
Parameter read ○
Inverter reset
Run command
(start, stop)
Running
frequency
5 (Ethernet
setting
board)
Monitor
Parameter write ○
Parameter read ○
Inverter reset
Ethernet
board Run command
(start, stop)
Other than
the above or Running
when the frequency
CC-Link IE setting
Field
Monitor
Network
Parameter write ×
Basic is
Parameter read ○
selected
Inverter reset
Run command
(start, stop)
Running
Communic frequency
ation —
monitor
option
Parameter write ×
Parameter read ○
Inverter reset
Inverter reset
External Run command
terminal at (start, stop)
—
the control
Running
circuit
frequency
setting
○: Enabled, ×: Disabled, Δ: Some are enabled
*1 As set in Pr.338 Communication operation command source, Pr.339 Communication speed command source.
*2 If an error occurs in the RS-485 communication or Ethernet communication, the inverter cannot be reset from the computer.
*3 Enabled only when stopped by the PU. At a PU stop, PS is displayed on the operation panel. The operation is as set in Pr.75 Reset selection/
disconnected PU detection/PU stop selection.
*4 Some parameters may be write-disabled according to the Pr.77 Parameter write selection setting and operating status.
Item
PU External
operation operation
○ ×
○ ×
○ ○
*4 *5
×
○
○ ○
× ×
× ×
○ ○
*5 *5
×
○
○ ○
○ ×
○ ×
○ ○
*4 *5
×
○
○ ○
× ×
× ×
○ ○
*5 *5
×
○
× ×
× ×
× ×
○ ○
*5 *5
×
○
× ×
○ ○
× ○
× ○
Controllability in each operation mode
External/ External/ NET
PU PU operation
combined combined (when RS-
operation operation 485
mode 1 mode 2 terminals
(Pr. 79 = 3) (Pr. 79 = 4) is used)
× ○ ×
○ × ×
○ ○ ○
*5 *5 *5
× × ×
○ ○ ○
○ ○ ○
× × ×
× × ×
○ ○ ○
*5 *5 *5
× × ×
○ ○ ○
○ ○ ○
× ○ ×
○ × ×
○ ○ ○
*4 *4 *5
○ ○ ×
○ ○ ○
○ ○ ○
× × ×
× × ○
○ ○ ○
*5 *5 *5
× × ×
○ ○ ○
× × ×
× × ×
× × ×
○ ○ ○
*5 *5 *5
× × ×
○ ○ ○
× × ×
○ ○ ○
*1
○ ×
×
*1
× ×
×
1.5 Setting of operation mode of the inverter
NET
NET operation
operation
(when a
(when the
communication
Ethernet
option is
connector
*8
used)
*6 *7
is used)
*1
×
○
*1
×
○
○ ○
*4 *5
○ ×
○ ○
*2
×
○
*1
×
○
*1
×
○
○ ○
*5 *4
× ○
○ ○
*2
×
○
1. OUTLINE
1
2
3
4
5
6
7
8
9
10
67