Mitsubishi Electric LAN CONTROL UTILITY Operation Manual
Lan control utility
Hide thumbs
Also See for LAN CONTROL UTILITY:
- User manual (30 pages) ,
- User manual (24 pages) ,
- User manual (30 pages)
Table of Contents
Advertisement
LAN CONTROL UTILITY
Operation Manual
1. Introduction ............................................................................................... 2
2. Setup ......................................................................................................... 4
3. Main screen............................................................................................... 7
4. Projector registration ............................................................................... 10
5. Operation of projector.............................................................................. 16
6. Schedule setting...................................................................................... 18
7. Mail setting .............................................................................................. 21
8. ProjectorView .......................................................................................... 22
9. Visual PA (Visual PA enabled projectors Only)....................................... 27
10. Telnet setup (Telnet enabled projectors only) ......................................... 28
11. PJLink ..................................................................................................... 29
12. Others ..................................................................................................... 31
1.1. Preparing to use network features.......................................................................... 2
1.2. Functions and features ........................................................................................... 2
1.3. Operation environment ........................................................................................... 2
2.2. When deleting "ProjectorView Global+" (Uninstallation)......................................... 5
2.3. Connection.............................................................................................................. 6
3.1. System settings ...................................................................................................... 9
4.2. When changing the projector IP settings .............................................................. 13
4.3. When changing projector settings ........................................................................ 13
4.4. When deleting projector registration ..................................................................... 15
5.1. Operation of projector by remote controller .......................................................... 16
5.2. Confirmation of projector status............................................................................ 17
6.1. Creation of projector group ................................................................................... 18
6.2. When changing group setting ............................................................................... 19
6.3. When deleting group............................................................................................. 20
7.1. Connection with mail server.................................................................................. 21
7.2. Mail setting............................................................................................................ 21
7.3. Sending test mail .................................................................................................. 21
8.1. Main functions....................................................................................................... 22
8.2. Starting ProjectorView .......................................................................................... 22
8.3. Entering projector information............................................................................... 24
8.4. Setting the network password............................................................................... 25
8.5. Resetting the network settings.............................................................................. 26
9.1. Starting Visual PA................................................................................................. 27
11.1. About PJLink......................................................................................................... 29
12.1. Troubleshooting .................................................................................................... 31
12.2. Supported Projectors ............................................................................................ 31
Contents
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric LAN CONTROL UTILITY
Summary of Contents for Mitsubishi Electric LAN CONTROL UTILITY
-
Page 1: Table Of Contents
LAN CONTROL UTILITY Operation Manual Contents 1. Introduction ....................2 1.1. Preparing to use network features................2 1.2. Functions and features ................... 2 1.3. Operation environment ................... 2 2. Setup ......................4 2.1. Installation of "ProjectorView Global+" ..............4 2.2. When deleting "ProjectorView Global+" (Uninstallation)......... 5 2.3. -
Page 2: Introduction
1. Introduction 1.1. Preparing to use network features • Installing the ProjectorView Global+ • Assigning the projector IP address • Configuring settings such as PASSWORD, Mail Setting, Language, and PJLink Certification Setting by running Telnet (Telnet-enabled models only) or using ProjectorView The projector IP address, password, and PJLink certification can be configured on the projector main screen. - Page 3 1. Introduction ® ® Microsoft and Windows are the registered trademark or trademark of Microsoft Corporation in the United States and other countries. (The official name of Windows is Microsoft Windows Operating System.) Pentium is the trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
-
Page 4: Setup
2. Setup 2.1. Installation of "ProjectorView Global+" Before starting installation, be sure to read "ReadMe.txt" contained in the CD-ROM. Copy "ProjectorView Global+.msi" contained in the TOOLS folder of CD-ROM to the hard disk of your personal computer. (1) Double click "ProjectorView Global+.msi", and start up the installer of "ProjectorView Global+". (2) The setup window is displayed. -
Page 5: When Deleting "Projectorview Global+" (Uninstallation)
2. Setup (5) When the installation has been completed, click [Close]. 2.2. When deleting "ProjectorView Global+" (Uninstallation) <Note> • When uninstalling "ProjectorView Global+", "ProjectorView Global+" should be ended in advance. If the application continues operating, uninstallation can not be performed normally. (1) Double click "ProjectorView Global+.msi", and start up the installer of "ProjectorView Global+". -
Page 6: Connection
2. Setup 2.3. Connection Connect the controller PC and the projector, which have installed "ProjectorView Global+", to a commercially available LAN cable. When connecting multiple projectors, use a commercially available hub. • A LAN terminal is required for the controller PC. •... -
Page 7: Main Screen
3. Main screen Menu bar Set Configuration Various settings can be configured, such as the new registration and editing of projector/group, mail setting, search range setting, or system setting. Global Control Automatic projector search and reloading of projector status can be carried out. - Page 8 3. Main screen EXIT You can exit "ProjectorView Global+". However, you cannot exit the application during the automatic projector search and the projector status loading. Even during the projector status acquisition, you can exit the application forcefully by clicking the button at the upper right corner of the main screen.
-
Page 9: System Settings
3. Main screen 3.1. System settings (1) Select "Edit System Info" from "Set Configuration" of the menu bar on the main screen. • "Edit System Info" window is displayed. (Default settings are shown in the following example.) Item Description Timeout duration for You can set the timeout duration of the projector search. -
Page 10: Projector Registration
4. Projector registration 4.1. Registration of projector to "ProjectorView Global+" The procedures to register projectors vary among the foregoing connection examples. • In connection examples 1 and 2 (where projectors are installed within the same local network), the projectors within such network are automatically detected and registered. For details, see procedure A below. •... - Page 11 4. Projector registration Procedure B - Connection example 3 (where projectors are installed via a router) To automatically detect projectors connected via a router, confirm the IP address in the projector network menu and specify a range of IP addresses to search that particular IP address using "Detect Projector". (1) Start up "ProjectorView Global+".
- Page 12 4. Projector registration <Note> • Set the default gateways of the projectors and PC correctly. For details, contact your network administrator. • Be sure to make a note of the IP addresses and default gateways you set. If you forget the setting values, you may not be able to detect the projectors again.
-
Page 13: When Changing The Projector Ip Settings
4. Projector Registration 4.2. When changing the projector IP settings You can change the projector IP settings. (1) Select the projector which you like to change from the projector list on the main screen. (2) Click [Assign IP] in the toolbar on the main screen. •... - Page 14 4. Projector registration • "Edit Projector Setting" window is displayed. (3) Set the Projector Name and its group and enable or disable the theft warning mail and the theft detector. Item Description Projector Name Input the projector name within 64 characters in one-byte alphanumeric symbol. MAC address The MAC address automatically acquired by the search is displayed.
-
Page 15: When Deleting Projector Registration
4. Projector registration 4.4. When deleting projector registration (1) Select the projector which you like to delete from the projector list on the main screen. (2) Select "Edit Projector Setting" from "Set Configuration" of the menu bar. • "Edit Projector Setting" window is displayed. (3) Click [Delete]. -
Page 16: Operation Of Projector
5. Operation of projector 5.1. Operation of projector by remote controller Group or single unit of projector can be operated. (1) Select the projector which you like to operate from the projector list on the main screen. • When selecting more than one projector simultaneously, select while pressing the Ctrl key. (2) Click [Remote Controller] of the tool bar on the main screen or when you like to operate a certain projector, double click the projector on the projector list on the main screen. -
Page 17: Confirmation Of Projector Status
5. Operation of projector 5.2. Confirmation of projector status The status of the projector can be confirmed. The status of the projector is displayed on the projector list on the main screen. Item Description Check Theft detector setting (ON/OFF) Projector list registration number Projector Name Projector name set in the application MAC address... -
Page 18: Schedule Setting
6. Schedule setting 6.1. Creation of projector group Multiple projectors can be controlled and batched by sorting groups. Also, each group can set each time of the power supply ON/OFF every day. Since the schedule of the power supply ON/OFF is performed by each group, the projector which you like to operate at the same schedule should be integrated into the same group. -
Page 19: When Changing Group Setting
6. Schedule setting (7) Click [Add]. <Note> • The power supply ON and the power supply OFF can not be selected at the same time of the same day of the week. • When starting up "ProjectorView Global+", the schedule operation can not be performed. •... -
Page 20: When Deleting Group
6. Schedule setting 6.3. When deleting group (1) Select the group which you like to delete from the Group select pull-down menu on the main screen. (2) Select "Edit Group Name" from "Set Configuration" of the menu bar. • "Edit Group Name" window is displayed. (3) Click [Delete]. -
Page 21: Mail Setting
7. Mail setting When the communication with the projector monitored by the theft detector is disrupted, a warning mail can be sent to the designated address, enabling to serve for early detection of the projector theft. The mail setting can not be set at every projector and every group. The same setting should be set for all projectors. 7.1. -
Page 22: Projectorview
8. ProjectorView ProjectorView is a web-browser based remote control and monitoring tool for network projectors. If you use the projectors listed in page 31, see ProjectorView in "LAN Control Utility" User Manual included with the projector. 8.1. Main functions • It displays the status of network projectors (such as the name of the projector, lamp temperature, lamp hours, errors and alerts). - Page 23 8. ProjectorView ProjectorView main window (REMOTE CONTROL) When you click REMOTE CONTROL, the Remote Control window is displayed. You can click the buttons displayed in the window to remotely control the projector. Buttons with red text show the projector's current status. The status displayed in this window is updated in regular intervals.
-
Page 24: Entering Projector Information
8. ProjectorView <Note> • No E-mail messages are sent when a command error occurs. • For approx. 10 seconds after the projector is powered on, the LAN and serial RS-232C commands cannot be controlled. • The LAN command has control priority over the RS-232C command when both commands are executed simultaneously. -
Page 25: Setting The Network Password
8. ProjectorView The following table explains each item. Item Description Projector name Enter a unique name to identity the projector. Installation date* Enter the date when the projector is installed. Projector location* Enter the place where the projector is located. SMTP IP address* Enter the IP address of the SMTP server used for sending e- mails.(e.g.192.168.0.1) -
Page 26: Resetting The Network Settings
8. ProjectorView (3) Enter the New network password and Confirm network password, and then click [OK]. • If passwords entered match, the window closes to save the changes. • If passwords entered do not match, an error window appears, and then the window returns to the SETUP window. -
Page 27: Visual Pa (Visual Pa Enabled Projectors Only)
9. Visual PA (Visual PA enabled projectors Only) Visual PA is a feature to display messages on the projector screen. It can be used for all active Visual PA enabled projectors. Visual PA is not available when using the projectors listed in page 31. 9.1. -
Page 28: Telnet Setup (Telnet Enabled Projectors Only)
• Press the [Enter] key within five seconds. If not, the connection is terminated and the [Enter] key is not recognized. If this happens, exit the command prompt and start it again. (4) Setup menus appear. For more information on telnet, see the LAN CONTROL UTILITY manual that comes with the projector. -
Page 29: Pjlink
Inquiry about the projector The projector name set on the ProjectorView Setup window is name returned. INF1? Inquiry about the "MITSUBISHI" is returned. manufacturer name INF2? Inquiry about the model Model name is returned. However, nothing is returned depending name on the model name. - Page 30 11. PJLink This projector, which is equipped with LAN terminal and manufactured by Mitsubishi Electric Corporation, is fully compliant to the specifications of JBMIA PJLink Class 1. It supports all the commands defined by PJLink Class 1, and the compliance has been verified with the PJLink standard specifications Version 1.0.
-
Page 31: Others
12.2. Supported Projectors • "Telnet" is available in the following types of projectors. For details, see "LAN Control Utility" User Manual included with the projector. • "Visual PA" is not available in the following types of projectors.