Cisco ATA186-I1 Administrator's Manual page 88

Operational Parameters
If method=1, set the following bits:
Bit 2—Reserved.
•
Bits 3-6—These bits are for the Start digit for known telephone numbers (valid values are 12 for
•
"A," 13 for "B," 14 for "C," and 15 for "D.").
Bits 7-10—These bits are for the End digit for known telephone numbers (valid values are 11 for
•
"#," 12 for "A," 13 for "B," 14 for "C," and 15 for "D.").
• Bits 11—This bit is for setting polarity reversal before and after the Caller ID signal (value of 0/1
disables/enables polarity reversal).
• Bits 12-16—These bits are for the maximum number of digits in the telephone number (valid values
are 1 to 32; the default is 15).
Bits 17-19—These bits are for the Start digit for unknown or restricted telephone numbers (valid
•
values are 4 for "A," 5 for "B," 6 for "C," and 7 for "D.").
Bits 20-22—These bits are for the End digit for unknown or restricted telephone numbers (valid
•
values are 3 for "#," 4 for "A," 5 for "B," 6 for "C," and 7 for "D.").
Bits 23-24—These bits are for the code that the Cisco ATA should send to the CID device if the
•
telephone number is unknown (valid values are 0 for "00", 1 for "0000000000", and 2 for "2"). The
value of 3 is reserved and should not be used.
Bits 25-26—These bits are for the code that the Cisco ATA should send to the CID device if the
•
telephone number is restricted (valid values are 0 for "10", and 1 for "1"). The values of 2 and 3 are
reserved and should not be used.
• Bit 27—Reserved.
Bit 28—Set to 1 to disable call-waiting caller ID on the Phone 1 port of the Cisco ATA.
•
Bit 29—Set to 1 to disable call-waiting caller ID on the Phone 2 port of the Cisco ATA.
•
Bit 30—Set to 1 to disable the callee-ID feature on the Phone 1 port of the Cisco ATA.
•
Bit 31—Set to 1 to disable the callee-ID feature on the Phone 2 port of the Cisco ATA.
•
If method=2, set the following bits:
Bit 2—Set to 0 to have the Cisco ATA transmit data prior to ringing by using the Ring-Pulse
•
Alerting Signal (RP-AS); set to 1 to have the Cisco ATA transmit data after the firsr ring.
Bits 3-8—Maximum number of digits in a phone number (valid values are 1 to 20; default is 12).
•
Bits 9-14—Maximum number of characters in a name (valid values are 1 to 20; default is 15).
•
Bit 15—If this bit is enabled (it is enabled by default), send special character O (out of area) to CID
•
device if telephone number is unknown.
Bit 16—If this bit is enabled (it is enabled by default), send special character P (private) to CID
•
device if telephone number is restricted.
Bits 17-27 are reserved.
•
Examples
The following examples are recommended values for the CallerID Method parameter:
Sweden = 0x0000ff61 or 0x006aff61
•
Denmark = 0x0000fde1 or 0x033efde1
•
USA = 0x00019e60
•
Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide for SCCP (version 3.0)
5-18
Chapter 5 Parameters and Defaults
OL-4652-01