2: Current Draw Worksheet For Idp Slc Devices - Honeywell Farenhyt Series Installation And Operation Manual

4. For notification appliance circuits and auxiliary devices not mentioned in the manual, refer to the device manual for the current
ratings.
5. Make sure that the total alarm current you calculated, including current for the panel itself, does not exceed 6.0 A. This is the
maximum alarm current for the IFP-300 control panel. If the current is above 6.0 A you will need to use a notification power
expander(s) such as the Honeywell 5496 NAC Expander, to distribute the power loads so that the IFP-300 or the power expanders
do not exceed their power rating. Refer to the current draw worksheets provided with the 5496 manual so you do not exceed their
power requirements.
6. Alternatively, you may network additional IFP-300ECS' to get additional power.
7. Complete the remaining instructions in the appropriate Current Draw Worksheet for determining battery size requirements.
3.7.2 Current Draw Worksheet for IDP SLC Devices
Use Table 3.2 to determine current requirements during alarm/battery standby operation when IDP SLC devices are installed. The IFP-
300 FACP supports up to a total of 300 SLC devices, consisting of any combination of Sensors and Modules.
For each device use this formula:
Fire Panel (Current draw from battery)
Addressable SLC Detectors
IDP-Photo
IDP-Photo-T
IDP-PhotoR
IDP-Ion
IDP-Heat
IDP-Heat-HT
IDP-Acclimate
IDP-Heat-ROR
IDP-Photo-W/IV
IDP-PHOTO-R-W/IV
IDP-PHOTO-T-W/IV
IDP-HEAT-W/IV
IDP-HEAT-ROR-W/IV
IDP-HEAT-HT-W/IV
IDP-Beam (without integral test)
IDP-Beam-T (with integral test)
3
DNR (non-Relay)
4
DNR (with Relay)
IDP-FIRE-CO
13
Number of
Device
Devices
This column
1
2
Table 3.2 Current Draw Worksheet for IDP SLC Devices
Current per Device
X This column
Standby:
Alarm:
Standby/Alarm:
SLC Standby:
Alarm:
SLC Standby:
Alarm:
SLC Standby:
Alarm:
SLC Standby:
Alarm:
SLC Standby:
Alarm:
SLC Standby:
Alarm:
SLC Standby/Alarm:
Aux. Pwr Standby:
Alarm:
SLC Standby/Alarm:
Aux. Pwr Standby:
Alarm:
None, included with IDP-PhotoR
None, included with IDP-PhotoR & IDP-Relay
SLC Standby:
Alarm:
IFP-300 / IFP-300ECS Manual P/N LS10145-001SK-E:B 12/18/2017
7
Standby
Current
= Current per number of devices.
190 mA 190 mA
250 mA
1
.30 mA
200mA
4.5mA
200mA
4.5mA
200mA
4.5mA
200mA
4.5mA
200mA
4.5mA
200mA
4.5mA
2 mA
2 mA
8.5 mA
2 mA
2 mA
8.5 mA
30 mA
7.2 mA
Alarm
Current
250 mA
mA mA
mA mA
mA mA
mA mA
mA mA
mA mA
mA mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA mA
mA
mA
mA mA
mA
mA
mA
mA