Canon Finisher-AK1 Service Manual page 6

Removing the Feed Guide Lower Static Eliminator ----------------------4-92
Removing the Disengagement Roller ----------------------------------------4-93
Removing the Thrust Unit -------------------------------------------------------4-95
Removing the Push-on Plate --------------------------------------------------4-97
Removing the Positioning Plate Unit -----------------------------------------4-98
Pulling out the Saddle Unit (service position) ------------------------------4-99
Removing the Saddle Inlet Static Eliminator ----------------------------- 4-100
Removing the Saddle Unit ---------------------------------------------------- 4-101
Removing the Press Unit ----------------------------------------------------- 4-102
Removing the Press Roller Unit --------------------------------------------- 4-105
Removing the Fold Roller ----------------------------------------------------- 4-108
Removing the Alignment Roller Unit --------------------------------------- 4-112
Removing the Alignment Roller --------------------------------------------- 4-113
Removing the Saddle Alignment Motor ----------------------------------- 4-113
5
Adjustment
Basic Adjustment --------------------------------------------------------------5-2
Outline -------------------------------------------------------------------------------- 5-2
Height Adjustment ----------------------------------------------------------------- 5-3
Side Registration/Skew Adjustment ------------------------------------------- 5-6
Adjusting Sensor Light Intensity -----------------------------------------------5-10
Adjustment at Time of Parts Replacement --------------------------- 5-12
Outline -------------------------------------------------------------------------------5-12
Adjusting Sensor Light Intensity -----------------------------------------------5-14
Adjusting Position of Tray A, B ------------------------------------------------5-16
Adjusting the Alignment Position
of the Upper Neat Alignment Plate -------------------------------------------5-17
Adjusting the Alignment Position
of the Lower Neat Alignment Plate -------------------------------------------5-19
Adjusting the Height of Corrugation Roller for Stack Delivery ---------5-21
Right Angle Adjustment of Alignment Plate---------------------------------5-25
Adjusting Alignment Plate Position -------------------------------------------5-26
Adjusting Position of Stapler ---------------------------------------------------5-28
Adjusting Staple Position (1-stapling at the rear) -------------------------5-29
Adjusting Staple Position (1-stapling at the front) ------------------------5-32
Adjusting Staple Position (2-stapling positions) ---------------------------5-35
Adjusting Delivery of Staple Stack (lower delivery) ----------------------5-37
Adjusting Delivery of Staple Stack (saddle delivery) ---------------------5-40
Saddle Stitch/Fold Placement Adjustment----------------------------------5-43
Adjusting Saddle Stitching Position ------------------------------------------5-47
Adjusting Saddle Folding Position --------------------------------------------5-49
Adjusting Position of Saddle Lead Edge Stopper-------------------------5-50
Adjustment After Replacing Finisher Controller PCB --------------------5-52
Bufferless Mode -------------------------------------------------------------------5-53
Adjustment in the Case of Failure in Stacking Performance
of Tray (upper curl) ---------------------------------------------------------------5-54
Adjustment in the Case of Failure in Stacking Performance
of Tray (lower curl) ----------------------------------------------------------------5-56
Adjustment in the Case of Failure in Stacking Performance
of Tray (run-on of paper when using thin paper) --------------------------5-58
Adjustment in the Case of Canceling Limit for Tray Stack--------------5-60
Adjusting Alignment for Saddle Stapling ------------------------------------5-62
Auxiliary Adjustment -------------------------------------------------------- 5-65
Outline -------------------------------------------------------------------------------5-65
Adjusting Position of Tray A, B ------------------------------------------------5-67
Adjusting Position of Feed Belt ------------------------------------------------5-68
Adjusting Staple Position (1-stapling at the rear) -------------------------5-70
Adjusting Staple Position (1-stapling at the front) ------------------------5-73
Adjusting Staple Position (2-stapling positions) ---------------------------5-76
Adjusting Delivery of Staple Stack (lower delivery) ----------------------5-78
Adjusting Delivery of Staple Stack (saddle delivery) ---------------------5-81
Saddle Stitch/Fold Placement Adjustment----------------------------------5-84
Adjusting Saddle Stitching Position ------------------------------------------5-88
Adjusting Saddle Folding Position --------------------------------------------5-90
Adjusting Position of Saddle Lead Edge Stopper-------------------------5-91
Adjusting Position for Saddle Alignment Width ----------------------------5-94
Bufferless Mode -------------------------------------------------------------------5-96
Adjusting Assist Stopper Position ---------------------------------------------5-97
Adjusting Height of Staple Inlet Guide ---------------------------------------5-98
Adjusting Paddle Height ------------------------------------------------------- 5-100
Adjustment in the Case of Failure in Stacking Performance
of Tray (upper curl) ------------------------------------------------------------- 5-102