Table of Contents
Advertisement
5
Adjustment > Auxiliary Adjustment > Outline
Auxiliary Adjustment
Outline
CAUTION: Setting the Dip Switch
If setting the Dip Switch, the Delivery Tray setting on the host machine side returns to
the default.
After setting the Dip Switch, it is necessary to execute the Delivery Tray setting on the
host machine side again.
Except for some items, the adjustment and setting can input from the both devices of the host
machine (service mode) and the finisher (Dip switch).
The input value is memorized in the EEPROM of finisher controller. Regardless of the input
device (host machine or finisher), the setting range and unit are same, and the final input
value is effective.
Bit setting of DSW1
Item
in the finisher
controller PCB
Bufferless Mode
ON:1, 3, 8
Adjustment in the Case
ON:1, 3, 6, 7
of Failure in Stacking
Performance of Tray
(upper curl)
Adjustment in the Case
ON:1, 3, 6, 7
of Failure in Stacking
Performance of Tray
(lower curl)
Adjustment in the Case
ON:1, 3, 7
of Failure in Stacking
Performance of Tray
(runon of paper when
using thin paper)
Adjustment in the Case
ON:1, 3, 5
of Canceling Limit for
Tray Stack
Setting of Pressless
ON:1, 3, 4
Mode
5
Adjustment > Auxiliary Adjustment > Outline
Service mode
Range Default
Reference
SORTER> OPTION
0 to 4
0
p. 5-96
>BUFFSW
SORTER>OPTION
0 to 2
0
p. 5-102
>CURLSW
SORTER>OPTION
0 to 2
0
p. 5-104
>CURLSW
SORTER>OPTION
0 to 1
0
p. 5-106
>TRYEJCT
SORTER>OPTION
0 to 1
0
p. 5-108
>TRYOVER
SORTER>OPTION
0 to 3
0
p. 5-120
>SDLPRS
At the occurrence of the following symptoms or at adjustment timing, perform the appropriate
adjustment.
Adjustment Type
Adjusting Position of
When replacing the Tray A/B Unit
Tray A, B
Adjusting Position of
When displacement occurs with delivered stack
Feed Belt
Adjusting Staple
When staple position (rear 1-point stapling) is displaced
Position (1-stapling at
the rear)
Adjusting Staple
When staple position (rear 1-point stapling) is displaced
Position (1-stapling at
the front)
Adjusting Staple
When staple position (2-point stapling) is displaced
Position (2-stapling
positions)
Adjusting Delivery of
When displacement of paper occurs (on the cover
Staple Stack (lower
and the 1st to 3rd sheets) at the time of stapled stack
delivery)
delivery (lower delivery)
Adjusting Delivery of
When displacement of paper occurs (on the cover
Staple Stack (saddle
and the 1st to 3rd sheets) at the time of stapled stack
delivery)
delivery (saddle delivery)
Saddle Stitch/Fold
When saddle stitch or fold position is displaced
Placement Adjustment
Adjusting Saddle
When stitch position (saddle delivery) is displaced
Stitching Position
Adjusting Saddle
When fold position (saddle delivery) is displaced
Folding Position
Adjusting Position of
When saddle fold position (saddle delivery) is displaced
Saddle Lead Edge
Stopper
Adjusting Position
When saddle alignment width is not correct
for Saddle Alignment
Width
Bufferless Mode
• When alignment failure occurs with the 2nd set (the
first 3 sheets) at the time of making multiple sets of
copy
• When paper corner bend occurs
• When Buffer Path 2 Sensor stationary jam (jam
code: 1109) occurs
Adjusting Assist
When the paper on the top of the stapled stack is
Stopper Position
misaligned
Adjusting Height of
• When stacking failure occurs on the tray with thin
Staple Inlet Guide
paper
• - When staple alignment failure occurs
T-5-8
Symptom, adjustment timing
5-65
Reference
p. 5-67
p. 5-68
p. 5-70
p. 5-73
p. 5-76
p. 5-78
p. 5-81
p. 5-84
p. 5-88
p. 5-90
p. 5-91
p. 5-94
p. 5-96
p. 5-97
p. 5-98
5-65
Advertisement
Table of Contents
