GE AF-650 GP Programming Manual page 113

Parameter Descriptions
PB-16 PCD Read Configuration
[10] Array
Option:
[1212] Torque [Nm]
[1213] Frequency
3 3
[1214] Motor current
[1215] Frequency [%]
[1217] Speed [RPM]
[1218] Motor Thermal
[1219] KTY sensor temperature
[1220] Motor Angle
[1221] Torque [%] High Res.
[1222] Torque [%]
[1223] Motor Shaft Power [kW]
[1224] Calibrated Stator Resistance
[1225] Torque [Nm] High
[1230] DC Link Voltage
[1232] Brake Energy /s
[1233] Brake Energy Average
[1234] Heatsink Temp.
[1235] Drive Thermal
[1238] Logic Controller State
[1239] Control Card Temp.
[1245] Motor Phase U Current
[1246] Motor Phase V Current
[1247] Motor Phase W Current
[1248] Speed Ref. After Ramp
[RPM]
[1250] External Reference
[1251] Pulse Reference
[1252] Feedback[Unit]
[1253] Digi Pot Reference
[1257] Feedback [RPM]
[1260] Digital Input
[1261] Terminal 53 Switch Setting
[1262] Analog Input 53
[1263] Terminal 54 Switch Setting
[1264] Analog Input 54
[1265] Analog Output 42 [mA]
[1266] Digital Output [bin]
[1267] Freq. Input #29 [Hz]
[1268] Freq. Input #33 [Hz]
[1269] Pulse Output #27 [Hz]
[1270] Pulse Output #29 [Hz]
[1271] Relay Output [bin]
[1272] Counter A
[1273] Counter B
[1274] Prec. Stop Counter
[1275] Analog In X30/11
[1276] Analog In X30/12
[1277] Analog Out X30/8 [mA]
[1284] Comm. Option STW
[1285] Drive Port CTW 1
[1287] Bus Readout Alarm/Warning
112
Function:
02/2016 All rights reserved.
PB-16 PCD Read Configuration
[10] Array
Option:
[1289] Configurable Alarm/
Warning Word
[1290] Alarm Word
[1291] Alarm Word 2
[1292] Warning Word
[1293] Warning Word 2
[1294] Ext. Status Word
[1295] Ext. Status Word 2
[1340] Analog Input X49/1
[1341] Analog Input X49/3
[1342] Analog Input X49/5
[1343] Analog Out X49/7
[1344] Analog Out X49/9
[1345] Analog Out X49/11
[1346] X49 Digital Output [bin]
[1500] Operating hours
[1501] Running Hours
[1502] kWh Counter
PB-18 Node Address
Range: Function:
126 [0 - Enter the station address in this parameter or,
*
126] alternatively, in the hardware switch. To adjust the
station address in parameter PB-18 Node Address,
set the hardware switch to 126 or 127 (all
switches set to ON). Otherwise, this parameter
shows the actual setting of the switch.
PB-22 Telegram Selection
Displays the Profibus message configuration.
Option:
[1] Standard telegram 1
[100] None
*
[101] PPO 1
[102] PPO 2
[103] PPO 3
[104] PPO 4
[105] PPO 5
[106] PPO 6
[107] PPO 7
[108] PPO 8
PB-23 Parameters for Signals
Array [1000]
Read only
Option: Function:
This parameter contains a list of signals available for
selection in parameter PB-15 PCD Write Configuration
and parameter PB-16 PCD Read Configuration.
Function:
Function:
Read only.
DET-618D