Siemens 6RA7086-6KS22 Operating Instructions Manual page 676

Connectors and binectors
Binector Name, description
B0054 Overrflow of actual position value
This binector changes to 1 when connector KK0046 (actual position value extended in software to a 32-bit
value) counts from value 7FFF FFFFH (= +2
Binector B0054 does not change back to 0 until connector KK0046 assumes a value other than 8000 0000H
31
(= –2 ) again.
Evaluation of the pulse encoder board SBP
Position acquisition of SBP, underflow
B0055
Position acquisition of SBP, overflow
B0056
Monitoring of the armature currents
1 = Commutation failure or overcurrent has occurred
B0057
Status word 1
B0100 Stat.word 1, bit 0:
Stat.word 1, bit 0 inverted
B0101
B0102 Stat.word 1, bit 1:
B0103 Stat.word 1, bit 1 inverted
Stat.word 1, bit 2:
B0104
Stat.word 1, bit 2 inverted
B0105
B0106 Stat.word 1, bit 3:
Stat.word 1, bit 3 inverted
B0107
Stat.word 1, bit 4:
B0108
B0109 Stat.word 1, bit 4 inverted
B0110 Stat.word 1, bit 5:
Stat.word 1, bit 5 inverted
B0111
B0112 Stat.word 1, bit 6:
B0113 Stat.word 1, bit 6 inverted
Stat.word 1, bit 7:
B0114
B0115 Stat.word 1, bit 7 inverted
B0116 Stat.word 1, bit 8:
Stat.word 1, bit 8 inverted
B0117
Stat.word 1, bit 10: 0=comparison setpoint not reached, 1=comparison setpoint reached
B0120
B0121 Stat.word 1, bit 10 inverted
Stat.word 1, bit 11: 0=undervoltage fault not active, 1=undervoltage fault active
B0122
Stat.word 1, bit11 inverted
B0123
B0124 Stat.word 1, bit 12: 0=main contactor request not active, 1=request to energize main contactor active
B0125 Stat.word 1, bit 12 inverted
Stat.word 1, bit 13: 0=ramp-function generator not active, 1=ramp-function generator active
B0126
B0127 Stat.word 1, bit 13 inverted
B0128 Stat.word 1, bit 14: 0=negative speed setpoint, 1=positive speed setpoint
Stat.word 1, bit 14 inverted
B0129
Status word 2
Stat.word 2, bit 18: 0=overspeed, 1=no overspeed
B0136
Stat.word 2, bit 18 inverted
B0137
B0138 Stat.word 2, bit 19: 0=no external fault 1 active, 1=external fault 1 active
B0139 Stat.word 2, bit 19 inverted
Stat.word 2, bit 20: 0=no external fault 2 active, 1=external fault 2 active
B0140
B0141 Stat.word 2, bit 20 inverted
B0142 Stat.word 2, bit 21: 0=no external alarm active, 1=external alarm active
12-28
31
–1) to value 8000 0000H (= –2
0=not ready to switch on, 1=ready to switch on
0=not ready, 1=ready (pulses disabled)
0=pulses disabled, 1=Run (output terminals energized)
0=no active fault, 1=active fault (pulses disabled)
0=OFF2 active, 1=no active OFF2
0=OFF3 active, 1=no active OFF3
0=no starting lockout (unit can be switched on), 1=starting lockout active
0=no active alarm, 1=alarm active
0=setp./act. val. deviation detected, 1=no setp./act. val. deviation
[SW 1.9 and later]
31
).
[SW 2.0 and later]
[SW 2.0 and later]
[SW 2.0 and later]
SIEMENS AG
SIMOREG DC Master Operating Instructions
05.05
Function
diag., Sheet
G145
Z120
Z120
G162
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G182
G183
G183
G183
G183
G183
G183
G183
6RX1700-0AD76