Siemens 6RA7086-6KS22 Operating Instructions Manual page 616

Parameter list
PNU Description
11.76 Setpoint reduction
U607 Source for activation of the setpoint reduction
(2607)
0 = Binector B0000
*
1 = Binector B0001
BDS
etc.
0 Setpoint reduction active
(G135)
The Setpoint (before the ramp-function generator) is multiplied
by the factor set in parameter U608
1 No setpoint reduction
U608 Multiplier for speed setpoint on activation of the setpoint reduction[SW
(2608) 1.6 and later]
FDS
(G135)
11.77 Definition of the function of inputs and outputs
U616 Control word for input "E stop" (term. 105 to 108)
(2616)
0 = E stop has same effect as OFF2
1 = E stop immediately cancels the firing pulse chain (without waiting for
I = 0 and without outputting α
(G117)
11.78 Definition of the function of the relay output at terminals 109 / 110
U619 Source for the relay output "line contactor ON" (terminals 109 / 110)
(2619)
*
0 = Binector B0000
BDS
1 = Binector B0001
etc.
(G117)
124 = Main contactor ON
11.79 Starting pulse – Speed controller
(See also Chapter 8 Function Diagram Sheet G150)
Starting pulse (integrator setting value for the speed controller)
U651
(2651)
FDS
(G150)
U652 Multiplier for starting pulse with neg. setpoint
(2652)
if the starting pulse acc. to U651 is also used for pos. setpoint
FDS
(G150)
U653 Starting pulse with neg. setpoint
(2653)
FDS
(G150)
U655 Source for Starting pulse
(2655)
0 = Connector K0000
*
1 = Connector K0001
(G150)
etc.
U656 Source for starting pulse with neg. setpoint
(2656)
0 = Connector K0000
*
1 = Connector K0001
(G150)
etc.
U657 Source for switchover starting pulse for pos./neg. setp.
(2657)
*
0 = Binector B0000
BDS
1 = Binector B0001
(G150)
etc.
11-152
[SW 1.6 and later]
[SW 2.0 and later]
)
w
[SW 1.7 and later]
[SW 1.7 and later]
[SW 1.7 and later]
[SW 1.7 and later] -100.00 to 100.00
[SW 1.7 and later]
[SW 1.7 and later]
[SW 1.7 and later]
Value range No. indices
[Unit] Factory
Steps setting
Type
All binector numbers Ind: 2
1 FS=1
Type: L2
0.00 to 100.00 Ind: 4
[%] FS=15.00
0.01% Type: O2
0 to 1 Ind: none
1 FS=0
Type: O2
All binector numbers Ind: 2
1 FS=124
Type: L2
-100.00 to 100.00 Ind: 4
[%] FS=0.00
0.01% Type: I2
0.00 to 200.00 Ind: 4
[%] FS=50.00
0.01% Type: O2
Ind: 4
[%] FS=0.00
0.01% Type: I2
All connector Ind: None
numbers FS=451
1 Type: L2
All connector Ind: None
numbers FS=452
1 Type: L2
All binector numbers Ind: 2
1 FS=0
Type: L2
SIEMENS AG
SIMOREG DC Master Operating Instructions
05.05
See
Change
(Access /
Status)
P052 = 3
P051 = 40
off-line
P052 = 3
P051 = 40
on-line
P052 = 3
P051 = 40
online
P052 = 3
P051 = 40
off-line
P052 = 3
P051 = 40
on-line
P052 = 3
P051 = 40
on-line
P052 = 3
P051 = 40
on-line
P052 = 3
P051 = 40
off-line
P052 = 3
P051 = 40
off-line
P052 = 3
P051 = 40
off-line
6RX1700-0AD76