Siemens 6RA7086-6KS22 Operating Instructions Manual page 474

Parameter list
PNU Description
r036 Display of field current controller setpoint
(G166)
r037 Display of actual EMF value
(G165)
r038 Display of actual armature voltage value
r039 Display of EMF setpoint
(G165) This parameter displays the EMF setpoint which is applied as the control
quantity in the field-weakening range.
This value is calculated from:
– Imotor
Umotor
rated
r040 Display of limitations:
Representation on operator panel (PMU):
Segment ON:
Segment OFF:
Segment or bit
0
1
2
3 ....... Negative current limit (armature) reached (K0132)
4 ....... Negative maximum speed reached (P513)
5 ....... Negative torque limit reached (B0203)
6 ....... Neg. limitation at ramp generator output reached (K0182)
7 ....... Neg. limitation at ramp generator input reached (K0197)
8 ....... α G limit (field) reached (P250)
9 ....... Positive current limit (field) reached (K0273)
10 ....... α G limit (armature) reached (P150)
11 ....... Positive current limit (armature) reached (K0131)
12 ....... Positive maximum speed reached (P512)
13 ....... Positive torque limit reached (B0202)
14 ....... Pos. limitation at ramp generator output reached (K0181)
15 ....... Pos. limitation at ramp generator input reached (K0196)
Note: This parameter has the same bit assignments as connector K0810.
Connector and binector displays
r041 High-resolution connector display:
i001: Display of connector selected in P042.01
(G121)
i002: Display of connector selected in P042.02
The display value is filtered with a time constant of 300ms (see Section 8,
Sheet G121)
P042 High-resolution connector display:
*
i001: Selection of connector to be displayed in r041.01
i002: Selection of connector to be displayed in r041.02
(G121)
The display value is filtered with a time constant of 300ms (see Section 8,
Sheet G121)
r043 Connector display:
i001: Display of connector selected in P044.01
(G121)
i002: Display of connector selected in P044.02
i003: Display of connector selected in P044.03
i004: Display of connector selected in P044.04
i005: Display of connector selected in P044.05
i006: Display of connector selected in P044.06
i007: Display of connector selected in P044.07
11-10
* RA (= P101 – P100 * P110)
rated
15 14 13 12 11 10
6 4
7 5 3 2
Corresponding limitation is reached
Corresponding limitation is not reached
α W limit (field) reached (P251)
Negative current limit (field) reached (K0274)
α W limit (armature) reached (α W acc. to P151
for continuous current, 165° for discontinuous current)
Speed limiting controller responds (B0201)
Speed limiting controller responds (B0201)
9 8
1 0
Value range No. indices
[Unit] Factory
Steps setting
Type
0.0 to 199.9 Ind: None
[% of P102] Type: O2
0.1% of P102
-1500.0 to 1500.0 Ind: None
[V] Type: I2
0.1V
-1500.0 to 1500.0 Ind: None
[V] Type: I2
0.1V
0.0 to 1500.0 Ind: None
[V] Type: O2
0.1V
Ind: None
Type: V2
-200.00 to 199.99 Ind: 2
[%] Type: I2
0.01%
All connector Ind: 2
numbers FS=0
1 Type: L2
-200.0 to 199.9 Ind: 7
[%] Type: I2
0.1%
SIEMENS AG
SIMOREG DC Master Operating Instructions
05.05
See
Change
(Access /
Status)
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P051 = 40
Online
P052 = 3
6RX1700-0AD76