Siemens 6RA7086-6KS22 Operating Instructions Manual page 546

Parameter list
PNU Description
P778 Delay for output value at binary output 4
The logic level at the binary selectable output changes only if the internal
(G112) signal level remains constant for the set delay period (internal signal level
changes which do not last as long as this delay period are not switched
through to the output)
11.41 Configuration of serial interfaces on basic converter
G-SST 1 (RS485 / RS232 on X300) (see also Section 8, Sheet G170 and Section 9)
P780 Selection of protocol for G-SST1 basic converter interface
*
0 Setting has no function
(G170)
2 USS protocol
8 for factory purposes
9 For internal factory test purposes
P781 Number of process data for G-SST1
*
When P780 = 0 or 9 is selected: Parameter is irrelevant
(G170)
When USS protocol (P780=2) is selected: Number of PZD elements
0 No process data are expected or sent in the USS protocol
1...16 Number of process data words in USS protocol (same number
applies to transmission and receipt)
The received PZD elements (1 to max. 16) are available at
connectors (K2001 to K2016) and, in some cases, bit-serially at
binectors for "internal wiring" purposes.
The PZD elements to be transmitted (1 to max. 16) are selected
in parameters P784.01 to P784.16.
P782 Length of parameter jobs for G-SST1
*
(G170)
This parameter is effective only when P780=2 (USS protocol).
0 No PKW data are expected or sent in the USS protocol.
3, 4 3 or 4 PKW data words are expected in the USS protocol and 3
or 4 PKW data words are also sent (for transmission of
parameter values).
127 Number of PKWs is determined by the telegram length
P783 Baud rate for G-SST1
*
1 300 baud
(G170)
2 600 baud
3 1200 baud
4 2400 baud
5 4800 baud
6 9600 baud
7 19200 baud
8 38400 baud
9 56700 baud
11 93750 baud
13 187500 baud
P784 Source for transmit data for G-SST1
*
Selection of connectors to be transferred as transmit data to the USS
(G170)
master via USS interface 1.
i001: Selection for word 1
i002: Selection for word 2
...
i016: Selection for word 16
Applicable settings:
0 = connector K0000
1 = connector K0001
etc.
11-82
Value range No. indices
[Unit] Factory
Steps setting
Type
0 to 10000 Ind: None
[ms] FS=0
1ms Type: O2
0, 2, 8, 9 Ind: None
1 FS=2
Type: O2
0 to 16 Ind: None
1 FS=2
Type: O2
0, 3, 4, 127 Ind: None
1 FS=127
Type: O2
1 to 13 Ind: None
1 FS=6
Type: O2
All connector Ind: 16
numbers FS=
1 i001: 32
i002: 167
i003: 0
i004: 33
i005-i016: 0
Type: L2
SIEMENS AG
SIMOREG DC Master Operating Instructions
05.05
See
Change
(Access /
Status)
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
6RX1700-0AD76