Mitsubishi Electric FR-A700 Technical Manual page 373

E700 D700
Signal Terminal Used
Depending on
[Pr. 178 to
E700
X14
184]
[Pr. 178 to
D700
182]
2
PU —
4
FUP
FDN
Depending on
[Pr. 190 to
E700
Pr. 192]
[Pr. 190,
D700
RL
Pr. 192]
PID
SLEEP
(Only in )
D700
SE SE
*1 When the X14 signal is not assigned, only the [Pr. 128
*2 The shaded area indicates the parameter initial value.
*3 When 100 or larger value is set in any of Pr.190 to Pr.192 (output terminal function selection), the terminal output has negative
logic. (Refer to page 61 for details)
*4 When [Pr. 561 PTC thermistor protection level
input. (Only in )
D700
*5 Refer to the LONWORKS communication option (FR-A7NL E kit) instruction manual for the setting method from LONWORKS
communication.
Refer to the CC-Link communication option (FR-A7NC E kit) instruction manual for the setting method from CC-Link
communication. (Only in
Function
PID control
selection
2 Set point input
Set point input
Measured value
4
input
Upper limit output
Lower limit output
Forward (reverse)
rotation direction
output
During PID control
activated
PID output
interruption
Output terminal
common
≠
≠ "9999"], terminal 2 is not available for set point input. Use [Pr. 133] for set point
)
E700
Description
Turn ON X14 signal to perform PID
control. ∗1
You can input the set point for PID
control.∗4
0 to 5V .............0 to 100%
0 to 10V ...........0 to 100%
Set the set point [Pr. 133] from the
operation panel.
Input the signal from the detector
(measured value signal).
4 to 20mA ........0 to 100%
0 to 5V .............0 to 100%
0 to 10V ...........0 to 100%
Output to indicate that the process value
signal exceeded the maximum value [Pr.
131].
Output when the process value signal
falls below the minimum value [Pr. 132].
"Hi" is output to indicate that the output
indication of the parameter unit is
forward rotation (FWD) or "Low" to
indicate that it is reverse rotation (REV)
or stop (STOP).
Turns ON during PID control.
Turns ON when the PID output
interruption function is performed.
Common terminal for open collector
output terminal.
0] setting makes PID control valid.
407
PARAMETER
Parameter Setting
Set 14 in any of
[ Pr. 178 to 184 ]
E700
[ Pr. 178 to 182]
D700
[ Pr. 128 = 20, 21 ]
[ Pr. 133 = 9999 ]
Pr. 73 = 1 ∗2 , 11 ]
[ Pr. 73 = 0, 10 ]
[ Pr. 128 = 20, 21 ]
[ Pr. 133 = 0 to 100% ]
[ Pr. 128 = 20, 21 ]
[ Pr. 267 = 0 ∗2 ]
[ Pr. 267 = 1 ]
[ Pr. 267 = 2 ]
[ Pr. 128 = 20, 21 ]
[ Pr. 131 ≠ 9999 ]
Set 15 or 115 ∗3 in
[Pr. 190 to Pr. 192]
E700
[ Pr. 190 or Pr. 192]
D700
[ Pr. 128 = 20, 21 ]
[ Pr. 132 ≠ 9999 ]
Set 14 or 114 ∗3 in
[Pr. 190 to Pr. 192]
E700
[ Pr. 190 or Pr. 192]
D700
Set 16 or 116 ∗3 in
[Pr. 190 to Pr. 192]
E700
[ Pr. 190 or Pr. 192]
D700
Set 47 or 147 ∗3 in
[ Pr. 190 to Pr. 192]
E700
[ Pr. 190 or Pr. 192]
D700
Pr. 575 ≠9999 ]
Set 70 or 170 ∗3 in [ Pr. 190 or
Pr.192]
2