Mitsubishi Electric FR-A700 Technical Manual page 143

2.1.2 FR-F700
In the initial setting, only the simple mode parameters are displayed. Set [Pr. 160 User group read selection] as required.
• indicates simple mode parameters.
• The parameters marked with in the table allow its setting to be changed during operation even if 0 (initial value) is
set in [Pr. 77 Parameter write selection] .
Initial
[Pr. ] Name
Value
160 User group read selection 9999
[Pr.] Name
Torque boost 0 to 30%
0
1 Maximum frequency 0 to 120Hz
Minimum frequency 0 to 120Hz
2
Base frequency 0 to 400Hz
3
4 Multi-speed setting (high speed) 0 to 400Hz
Multi-speed setting (middle speed) 0 to 400Hz
5
Multi-speed setting (low speed) 0 to 400Hz
6
Acceleration time 0 to 3600/360s
7
Deceleration time 0 to 3600/360s
8
9 Electronic thermal O/L relay 0 to 500/0 to 3600A
10 DC injection brake operation frequency 0 to 120Hz, 9999
11 DC injection brake operation time 0 to 10s
12 DC injection brake operation voltage 0 to 30%
— 13 Starting frequency 0 to 60Hz
— 14 Load pattern selection 0, 1
15 Jog frequency 0 to 400Hz
16 Jog acceleration/deceleration time 0 to 3600/360s
— 17 MRS input selection 0, 2
— 18 High speed maximum frequency 120 to 400Hz
— 19 Base frequency voltage 0 to 1000V, 8888, 9999
Acceleration/deceleration reference
20 1 to 400Hz
frequency
21 Acceleration/deceleration time increments 0, 1
22 Stall prevention operation level 0 to 150%, 9999
Stall prevention operation level
23 0 to 200%, 9999
compensation factor at double speed
24 Multi-speed setting (speed 4) 0 to 400Hz, 9999
25 Multi-speed setting (speed 5) 0 to 400Hz, 9999
26 Multi-speed setting (speed 6) 0 to 400Hz, 9999
27 Multi-speed setting (speed 7) 0 to 400Hz, 9999
PARAMETER
Setting
Remarks
Range
9999 Only the simple mode parameters can be displayed.
0 Simple mode+extended mode parameters can be displayed.
Only the parameters registered to the user group can be
1
displayed.
Minimum Setting
Setting Range Initial value Reference
Increments
6/4/3/2/
0.1%
1.5/1% *1
0.01Hz 120/60Hz
*2
0.01Hz 0Hz
0.01Hz 60Hz
0.01Hz 60Hz
0.01Hz 30Hz
0.01Hz 10Hz
0.1/0.01s 5/15s
*3
0.1/0.01s 10/30s
*3
Rated inverter
0.01/0.1A
*2 *2
current
0.01Hz 3Hz
0.1s 0.5s
0.1% 4/2/1%
*4
0.01Hz 0.5Hz
1 1
0.01Hz 5Hz
0.1/0.01s 0.5s 215, 234
1 0
0.01Hz 120/60Hz
*2
0.1V 9999
0.01Hz 60Hz
1 0
0.1% 120%
0.1% 9999
0.01Hz 9999
0.01Hz 9999
0.01Hz 9999
0.01Hz 9999
152
• Symbols in the option column indicate parameters which function when an option is mounted.
......... FR-A7AX,
......... FR-A7NC,
......... FR-A7NP
• These instruction codes are used for parameter read and write by using Mitsubishi inverter protocol with the RS-485
communication.
• Symbols in the control mode-based correspondence table indicate the following;
: Usable parameter
×: Unusable parameter
• Symbols in the parameter copy, parameter clear, and all parameter clear columns indicate the following;
: Valid
×: Invalid
[Pr.] Option
244 0
232
1
232 2
244 3
216
4
216 5
216 6
234 7
234 8
379
9
328 10
328 11
328 12
232 13
244
14
215
15
16
56 17
232 18
244
19
234
20
234
21
335 22
335 23
216
24
216 25
216 26
216
27
.......... FR-A7AY, .......... FR-A7AR,
......... FR-A7ND, ......... FR-A7NL,
Control Mode-based
Instruction Code
Correspondence Table
Simple
V/F magnetic
Read Write Extended
control flux vector
control
×
00 80 0
01 81 0
02 82 0
03 83 0
04 84 0
05 85 0
06 86 0
07 87 0
08 88 0
09 89 0
0A 8A 0
0B 8B 0
0C 8C 0
0D 8D 0
0E 8E 0
0F 8F 0
10 90 0
11 91 0
12 92 0
13 93 0
14 94 0
15 95 0
16 96 0
17 97 0
18 98 0
19 99 0
1A 9A 0
1B 9B 0
152
PARAMETER
Parameter Parameter All Parameter
Copy Clear Clear
2