Toshiba Perfecptione Installation And Maintenance Manual page 234

PROGRAMMING PROCEDURES
SECTION 200-255-313
FEBRUARY 1992
3. Message Registration Data Block (Table
13-3)
3.01 TheMessage Registration DataBlock(DMRD
Program) defines all parameters for the Message
Registration feature.
REQ (Request)-Indicates that the program has
loaded. Two responses are possible:
CHG-To change an existing Data Block.
OUT-To delete an existing Data Block.
ICC (Interchangeable Codes)-A "Y" informs the
system that interchangeable codes are ,used.
These are office codes that have 0 or 1 as the
second digit (NO/i X format). Area codes will be
identified as the three digits following the DDD
prefix. Office codes will be identified as the first
three digits when a DDD prefix is not dialed (see
DDP prompt).
Enter: Y or N.
DDP (Direct Distance Dialing Prefix)-Defines the
Direct Distance Dialing (DDD) prefix in the Num-
bering Plan Area (NPA). If ICC is "Y," then NO/l X
and NXX become interchangeable, enabling area
codes and office codes to have 0 or 1 as their
second digit. In this case, the DDP is used to
differentiate between the two code types (see
example). If the ICC response is "N", then calls
will be made using the normal NPA formula of
NO/lx and NNX.
Enter: 1, 2, or 3 digits or NONE.
Example: If ICC is "Y" and the DDP is pro-
grammed as 1, then the dialed num-
ber 209-1234 is recognized as a call
within the home area code, while the
dialed number 1-209-555-l 234 is
recognized as acall outside the home
area code. If ICC is "N", this dialing
plan is not used.
HAC (Home Area Code)-Defines the area code
in which the system is operating. A home area
code is also used to analyze dialed numbers
which do not contain an area code. Data entered
here will appear in theToll Restriction Data Block
(DTOL Program, PAR table, HAC prompt).
Enter: Area Code (NO/l X).
SVT (Supervision Time)-Defines the time al-
lowed for a call to be connected before the First
Billing Interval begins. This timer will start when
the system accesses a trunk during an outgoing
local call.
Enter: 0 - 120 (time in seconds).
TNl-TN5 (Rate Tables 1 - 5)-These prompts
require no user entry. They wiil be followed by
prompts which request parameters for the op-
eration of the Message Registration features.
FBI (First Billing Interval)-Defines the interval
time for the first billing interval.
Enter: 1 - 180 (time in seconds).
FBU (First Billing Unit)-Defines the number of
billing units per first billing interval.
Enter: 0 - 100.
IBI (Incremental Billing Interval)-Defines the
interval time for each incremental billing interval.
Enter: 1 - 180 (time in seconds).
IBU (Incremental Billing Units)-Defines the
number of billing units per incremental billing
interval.
Enter: 0 - 100.
CST (Unit Cost)-Defines the cost per each billing
unit.
Enter: 1 - 500 (cost in cents).
OCA (Office Codes-Add)-Indicates the office
codes that are to be added to the office code
table and defines the calls that are to be billed
according to one of the five Rate Tables. Office
codes may be added either by using single 3-
digit codes or by using 4-digit range codes.
Enter: NXXX NXX NXXX etc.
OCD (Off ice Codes-Delete)-indicates the off ice
codes that are to be deleted from the office code
table. Office codes may be deleted either by
using single 3-digit codes or by using 4-digit
range codes.
Enter: NXXX NXX NXXX etc.
NOTE:
N=2-9, X=0-9.
13-4