Table of Contents
Advertisement
PROGRAMMINGPROCEDURES
SECTION 200-255-309
FEBRUARY1992
NOTES:
TABLE 9-3 (continued)
1. NN = trunk PCB number,
X = circuit number
1 - 4 .
2. Used only for PERCEPTIONex
systems,
for trunks assigned
above T15.
3. GG = trunk group number
(00 - 15).
MM = unique trunk number
within group (00 - 63).
15MM = Private Line
or
PVLMM
= Private Line
4.
5.
6.
7.
GMN cannot
be changed.
The Data Block must be removed
(OUT) and NEW data must be
entered.
8.
The characters
available
for trunk names are A - Z, 0 - 9, [space]. A maximum
of 16 alphanumeric
charaters
are allowed
for each name. for CO, FX, WATS trunks only.
This prompt
only appears
for Trunk Group
15 (PVL). TDN is the DN assigned
to a private trunk
line (1 - 3 digits).
Enter Trunk's Night Directory
Number
(1 - 4 digits).
This number
can also be changed
by the
attendant
when making
night assignments
(no meaning
for TIuCCSA/DID/PVL
trunks).
This
number
must match the REM entry in the DSYS Program
in order to activate
Remote
Access to
Services.
Enter Trunk's Day Directory
Number
(1 - 4 digits). Up to 8 numbers
may be entered,
for either
immediate
or delayed
ringing.
Indicate
delayed
ringing
for a specific station by entering
i im-
mediately
after the station number.
Day number(s)
can also be changed
by the attendant.
The Attendant
Console(s)
CANNOTbe
included as part of delayed ringing. i.e., lfA770
is entered
at the DA Yprompt,
no other entries are allowed. ACD pilot numbers
also CANNOT
be entered as
part of delay ringing. i.e., If an ACD pilot number
is entered
at the DAY prompt,
no other entries
are allowed.
9. If TEN = Yin the DSYS Data Block and trunks are assigned
to TEN = 0 in DTGP, calls will ring only
at Attendant
0; if the trunks are assigned
to TEN = 1 in DTGP, calls will ring only at Attendant
1.
If TEN = N in the DSYS Data Block, only ATO
can be entered
and calls will load share between
ATT0 and ATT1 in a two-console
operation.
NONE = Calls will activate
the UNA device.
10.
11.
12.
13.
14.
This entry assigns the destination
of a Transfer
Recall on this trunk.
OPC = Originating
Party Control.
FPR = First Party Release.
This prompt
only appears
for TlffCCSA/DID
trunks.
Outgoing
dialing method:
PlO = rotary dial 10 PPS. P20 = rotary dial 20 PPS.
TON = DTMF.
The OTR prompt
appears
only when a trunk is assigned
to Trunk Group 15 (PVL). Following
the
OTR prom
t, the system will prompt D and any entries made will be deleted.
To add a station port,
press the &I - key. The system
will then prompt A and any entries made will be added.
Each private
line can have up to 96 line appearances,
each of which can be individually
restricted by using OTR.
When programming
these station ports, up to 10 ports may be entered
in a single line.
15.
16.
Is Answer
Supervision
required
to the calling party?
Y = yes; N = no.
= Ignore line entered.
Backspace.
Stop printing
and return to REQ.
Exit Program.
9-11
Advertisement
Chapters
Table of Contents
