Siemens SINUMERIK 828D Operating Manual page 15
Computerized numerical controller for machine tools
Hide thumbs
Also See for SINUMERIK 828D:
- Function manual (1799 pages) ,
- Commissioning manual (1167 pages) ,
- Programming manual (822 pages)
Table of Contents
Advertisement
9.2.8
Cut-off (CYCLE92) ................................................................................................................ 388
9.3
Contour turning ..................................................................................................................... 390
9.3.1
General information .............................................................................................................. 390
9.3.2
Representation of the contour .............................................................................................. 391
9.3.3
Creating a new contour ......................................................................................................... 392
9.3.4
Creating contour elements .................................................................................................... 394
9.3.5
Entering the master dimension ............................................................................................. 400
9.3.6
Changing the contour............................................................................................................ 402
9.3.7
Contour call (CYCLE62) - only for G code program ............................................................. 403
9.3.8
Stock removal (CYCLE952) .................................................................................................. 404
9.3.9
Stock removal rest (CYCLE952) ........................................................................................... 412
9.3.10
Plunge-cutting (CYCLE952) ................................................................................................. 415
9.3.11
Plunge-cutting rest (CYCLE952) .......................................................................................... 420
9.3.12
Plunge-turning (CYCLE952) ................................................................................................. 423
9.3.13
Plunge-turning rest (CYCLE952) .......................................................................................... 429
9.4
Milling .................................................................................................................................... 431
9.4.1
Face milling (CYCLE61) ....................................................................................................... 431
9.4.2
Rectangular pocket (POCKET3) ........................................................................................... 435
9.4.3
Circular pocket (POCKET4) .................................................................................................. 444
9.4.4
Rectangular spigot (CYCLE76) ............................................................................................ 454
9.4.5
Circular spigot (CYCLE77) ................................................................................................... 461
9.4.6
Multi-edge (CYCLE79) .......................................................................................................... 468
9.4.7
Longitudinal groove (SLOT1) ................................................................................................ 473
9.4.8
Circumferential groove (SLOT2) ........................................................................................... 482
9.4.9
Open groove (CYCLE899) .................................................................................................... 490
9.4.10
Long hole (LONGHOLE) - only for G code program ............................................................ 501
9.4.11
Thread milling (CYCLE70) .................................................................................................... 503
9.4.12
Engraving (CYCLE60) .......................................................................................................... 507
9.5
Contour milling ...................................................................................................................... 514
9.5.1
General information .............................................................................................................. 514
9.5.2
Representation of the contour .............................................................................................. 514
9.5.3
Creating a new contour ......................................................................................................... 516
9.5.4
Creating contour elements .................................................................................................... 519
9.5.5
Changing the contour............................................................................................................ 524
9.5.6
Contour call (CYCLE62) - only for G code program ............................................................. 525
9.5.7
Path milling (CYCLE72) ........................................................................................................ 526
9.5.8
Contour pocket/contour spigot (CYCLE63/64) ..................................................................... 532
9.5.9
Predrilling contour pocket (CYCLE64) .................................................................................. 534
9.5.10
Milling contour pocket (CYCLE63) ........................................................................................ 538
9.5.11
Contour pocket residual material (CYCLE63, option) ........................................................... 544
9.5.12
Milling contour spigot (CYCLE63) ......................................................................................... 547
9.5.13
Contour spigot residual material (CYCLE63, option) ............................................................ 552
9.6
Further cycles and functions ................................................................................................. 555
9.6.1
Swiveling plane / aligning tool (CYCLE800) ......................................................................... 555
9.6.2
Swiveling tool (CYCLE800) .................................................................................................. 563
9.6.2.1
Aligning turning tools - only for G code program (CYCLE800) ............................................. 563
9.6.2.2
Aligning milling tools - only for G code program (CYCLE800).............................................. 566
9.6.2.3
Preloading milling tools - only for G code program (CYCLE800) ......................................... 567
9.6.3
High-speed settings (CYCLE832) ......................................................................................... 568
9.6.4
Subroutines ........................................................................................................................... 572
Turning
Operating Manual, 01/2015, 6FC5398-8CP40-5BA2
Table of contents
15
Advertisement
Table of Contents
