Alarm Time Removed In Days / T_Alarm Res Days; Delete Fault Buffer Of All Drive Objects / Del Fault Buffer; Bi: Rfg Active / Rfg Active; Monitoring Configuration / Monit Config - Siemens SINAMICS G150 Manual

2 Parameters
2.2 List of parameters
r2146[0...63]

Alarm time removed in days / t_alarm res days

All objects Can be changed: -
Data type: Unsigned16
P-Group: Messages
Not for motor type: -
Min
-
Description: Displays the system runtime in days when the alarm was cleared.
Dependency: Refer to: r2110, r2114, r2122, r2123, r2124, r2125, r2134, r2145, r3121, r3123
Notice: The time comprises r2146 (days) and r2125 (milliseconds).
Note: The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
p2147

Delete fault buffer of all drive objects / Del fault buffer

CU_G130_DP, Can be changed: U, T
CU_G130_PN,
Data type: Integer16
CU_G150_DP,
P-Group: Displays, signals
CU_G150_PN
Not for motor type: -
Min
0
Description: Setting to delete the fault buffer of all existing drive objects.
Value: 0:
1:
Dependency: Refer to: r0945, r0947, r0948, r0949, r2109, r2130, r2133, r2136
Note: p2147 is automatically set to 0 after execution.
p2148[0...n]

BI: RFG active / RFG active

VECTOR_G Can be changed: U, T
Data type: Unsigned32 / Binary
P-Group: Messages
Not for motor type: -
Min
-
Description: Sets the signal source for the signal "ramp-function generator active" for the following signals/messages:
"Speed setpoint - actual value deviation within tolerance t_on" (BO: r2199.4)
"Ramp-up/ramp-down completed" (BO: r2199.5)
Notice: The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note: The binector input is automatically pre-assigned to r1199.2.
The following applies for SERVO:
The pre-assignment using the automatic calculation of the motor/control parameters in the drive (p0340 = 1, 3, 5) is
only realized if, at the instant of the calculation, the "setpoint channel" function module is active (r0108.8 = 1). If the
calculation in p0340 is not selected when downloading parameters, then the parameter is not preassigned.
p2149[0...n]

Monitoring configuration / Monit config

VECTOR_G Can be changed: U, T
Data type: Unsigned16
P-Group: Messages
Not for motor type: -
Min
-
Description: Sets the configuration for messages and monitoring functions.
516
Inactive
Start to delete the fault buffer of all drive objects
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
1
Calculated:
CALC_MOD_LIM_REF
Dyn. index: CDS, p0170
Units group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: DDS, p0180
Units group: -
Scaling: -
Max
-
List Manual (LH2), 04/2014, A5E03263479A
Access level: 3
Func. diagram: 8065
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 4
Func. diagram: 8060
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: 8011
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0000 0000 0000 0001 bin
SINAMICS G130/G150