Pn Subslot Controller Assignment / Pn Subslot Assign; Pn Ip Address Remote Controller 1 / Ip Addr Rem Ctrl1; Pn Ip Address Remote Controller 2 / Ip Addr Rem Ctrl2; Profisafe Wait For Clock Synchronization / Ps Wait Sync - Siemens SINAMICS G150 Manual

2 Parameters
2.2 List of parameters
r8960[0...2]

PN subslot controller assignment / PN subslot assign

B_INF, CU_G130_DP, Can be changed: -
CU_G130_PN,
Data type: Unsigned8
CU_G150_DP,
P-Group: -
CU_G150_PN, ENC,
Not for motor type: -
TB30, TM150, TM31,
VECTOR_G
Min
0
Description: Displays the controller assignment of a PROFINET subslot on the actual drive object.
Index: [0] = Subslot 2 PROFIsafe
[1] = Subslot 3 PZD telegram
[2] = Subslot 4 PZD supplementary data
Dependency: Refer to: r8961, r8962
Note: Example:
If the parameter contains the value 2 in index [1], then this means that subslot 3 is assigned to controller 2.
r8961[0...3]

PN IP Address Remote Controller 1 / IP Addr Rem Ctrl1

CU_G130_PN, Can be changed: -
CU_G150_PN
Data type: Unsigned8
P-Group: -
Not for motor type: -
Min
0
Description: Displays the IP address of the first PROFINET controller connected with the device via PN onboard.
r8962[0...3]

PN IP Address Remote Controller 2 / IP Addr Rem Ctrl2

CU_G130_PN, Can be changed: -
CU_G150_PN
Data type: Unsigned8
P-Group: -
Not for motor type: -
Min
0
Description: Displays the IP address of the second PROFINET controller connected with the device via PN onboard.
p8969

PROFIsafe wait for clock synchronization / PS wait sync

CU_G130_DP, Can be changed: U, T
CU_G130_PN,
Data type: Integer16
CU_G150_DP,
P-Group: -
CU_G150_PN
Not for motor type: -
Min
0
Description: Setting for the behavior of a PROFIsafe communication connection depending on another isochronous
communication connection.
Value: 0:
1:
Recommend.: A value of 1 is recommended, if problems are encountered with the PROFIsafe connection when synchronizing.
Note: If value = 1:
A PROFIsafe connection is only accepted if an isochronous connection exists.
Relevant, if PROFIsafe and isochronous operation are configured via various communication connections (e.g.
PROFINET Shared Device).
832
No
Yes
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
8
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
1
List Manual (LH2), 04/2014, A5E03263479A
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
SINAMICS G130/G150