D-Link xStack DGS-3420 Series Reference Manual page 135

xStack® DGS-3420 Series Layer 2 Managed Stackable Gigabit Switch CLI Reference Guide
<value 0-63>] {counter [enable | disable]}} exceed [permit {replace_dscp <value 0-63>} | drop]
{counter [enable | disable]} violate [permit {replace_dscp <value 0-63>} | drop] {counter [enable
| disable]} | sr_tcm cir <value 0-1048576> cbs <value 0-131072> ebs <value 0-131072>
{[color_blind | color_aware]} {conform [permit | replace_dscp <value 0-63>] {counter [enable |
disable]}} exceed [permit {replace_dscp <value 0-63>} | drop] {counter [enable | disable]}
violate [permit {replace_dscp <value 0-63>} | drop] {counter [enable | disable]} | delete]
Parameters
profile_id - Specify the index of the access list profile.
<value 1-6> - Specify the value between 1 and 6.
profile_name - Specify the name of the profile.
<name 1-32> - Specify the name of the profile. The maximum length is 32 characters.
access_id - Specify the index of the access list entry.
<value 1-256> - Specify the value between 1 and 256.
rate - Specify the rate for single rate two color mode. Specify the committed bandwidth in Kbps for
the flow.
<value 0-1048576>- Specify the value between 0 and 1048576.
burst_size - (Optional) Specify the burst size for the single rate two color mode. The unit is Kbyte.
<value 0-131072> - Specify the value between 0 and 131072.
rate_exceed - Specify the action for packets that exceed the committed rate in single rate two color
mode. The action can be specified as one of the following:
drop_packet - Drop the packet immediately.
remark_dscp - Mark the packet with a specified DSCP. The packet is set to drop for packets with
a high precedence.
<value 0-63> - Specify the value between 0 and 63.
tr_tcm - Specify the "two-rate three-color mode."
cir -Specify the Committed Information Rate. The unit is Kbps. CIR should always be equal or
less than PIR.
<value 0-1048576> - Specify the value between 0 and 1048576.
cbs - (Optional) Specify the Committed Burst Size. The unit is Kbyte.
<value 0-131072> - Specify the value between 0 and 131072.
pir - Specify the Peak information Rate. The unit is Kbps. PIR should always be equal to or
greater than CIR.
<value 0-1048576> - Specify the value between 0 and 1048576.
pbs - (Optional) Specify the Peak Burst Size. The unit is Kbyte.
<value 0-131072> - Specify the value between 0 and 131072.
color_blind - Specifies the meter mode as color-blind. The default is color-blind mode.
color_aware - Specifies the meter mode as color-aware. The final color of the packet is determined
by the initial color of the packet and the metering result.
conform - (Optional) This field denotes the green packet flow. Green packet flows may have their
DSCP field rewritten to a value stated in this field. Users may also choose to count green packets
by using counter parameter.
permit - Enter this parameter to allow packet flows that are in the green flow.
replace_dscp - Packets that are in the green flow may have their DSCP field rewritten using this
parameter and entering the DSCP value to replace.
<value 0-63> - Specify the value between 0 and 63.
counter - (Optional) Use this parameter to enable or disable the packet counter for the specified
ACL entry in the green flow.
enable - Enable the packet counter for the specified ACL entry in the green flow.
disable - Disable the packet counter for the specified ACL entry in the green flow.
exceed - This field denotes the yellow packet flow. Yellow packet flows may have excess packets
permitted through or dropped. Users may replace the DSCP field of these packets by checking its
radio button and entering a new DSCP value in the allotted field.
130