Yamaha SIGMA-G5SII Service Information page 3

2.6.6. "FDR BASE" Window ........................................................................................................ 74
2.7. Manual Operation ................................................................................................................. 74
2.7.1. Unit Adjustment ................................................................................................................ 75
2.7.1.1. Linear Measure Detection Test ..................................................................................... 75
2.7.1.2. Cutter Operation ............................................................................................................ 75
2.7.2. Device Check (Input/Output) ............................................................................................ 76
2.7.2.1. Manual Operation of Each Section ............................................................................... 76
2.7.3. Manual Axis Operation ..................................................................................................... 76
《Example: In the case that the nozzle does not touch the jig》 ................................ 77
2.7.3.1.
2.8. System Data Editing Procedure ........................................................................................... 77
2.9. Change Procedure to Debug Mode ....................................................................................... 80
2.9.1. Main Additional Items in the "Debug Mode" ................................................................... 82
2.9.2. Escape from Debug Mode .................................................................................................. 82
3. Mechanism ............................................................................................................................... 83
3.1. Nozzle Stocker Unit Change Procedure ............................................................................... 83
3.1.1. Removal of the Nozzle Stocker Unit ................................................................................. 83
3.1.2. Attachment of the Nozzle Stocker Unit ............................................................................ 83
3.1.3. Description of Connecting Connector ............................................................................... 84
3.1.4. Connection Example .......................................................................................................... 85
3.1.4.1. Nozzle Stocker Configuration High - High - High - High ........................................... 85
3.1.4.2. High - High - None - Multi ............................................................................................. 86
3.1.4.3. Multi - None - None - None ............................................................................................ 87
3.1.4.4. Multi - None - High - High ............................................................................................. 88
3.1.4.5. Multi - None - None - High ............................................................................................ 89
3.1.4.6. Multi - None - None - Multi ........................................................................................... 90
3.1.5. Various Settings ................................................................................................................. 91
3.1.5.1. High-Speed Nozzle Stocker ............................................................................................ 91
3.1.5.2. Multi Functional Nozzle Shutter .................................................................................. 92
3.1.5.3. Nozzle Up-Status Detection Sensor Amplifier Adjustment ........................................ 93
3.2. X-Axis Ball Screw Change Procedure .................................................................................. 96
3.2.1. X-Axis Ball Screw Removal Procedure ............................................................................. 96
3.2.2. X-axis Linear Guide Attachment Procedure .................................................................... 98
3.2.3. Treatment if any value is out of the standard range: .................................................... 100
Adjustment Procedure ① ............................................................................................ 100
3.2.3.1.
Adjustment Procedure ② ............................................................................................ 100
3.2.3.2.
3.3. Y-axis Linear Guide Attachment ........................................................................................ 101
3.4. X-axis Linear Guide Attachment ........................................................................................ 103
3.5. X-Axis Linear Scale Change Procedure ............................................................................. 106
3.5.1. X-Axis Linear Scale Removal .......................................................................................... 106
3.5.2. X-Axis Linear Scale Attachment..................................................................................... 106
3.6. Y-Axis Linear Scale Change Procedure ............................................................................. 109
3.6.1. Y-Axis Linear Scale Removal .......................................................................................... 109
3.6.2. Y-Axis Linear Scale Attachment..................................................................................... 109
3.7. X-Axis Scale Head Adjustment Procedure ......................................................................... 112
3.7.1. Preparation of Adjusting Jig ........................................................................................... 112
3.7.2. Adjusting Procedure ........................................................................................................ 113
3.8. Y-Axis Scale Head Adjustment Procedure ......................................................................... 117
3.8.1. Preparation of Adjusting Jig ........................................................................................... 117
3.8.2. Adjusting Procedure ........................................................................................................ 118
4. Maintenance ........................................................................................................................... 120
4.1. CPU-1 PCBs U91 and U92 Change .................................................................................... 120
4.1.1. Removal of CPU1-BOX .................................................................................................... 120
4.1.2. Removal of Control Board U91 or U92 ........................................................................... 121
Service Information
SI1705004E-00=SIGMA-G5SII Service Manual
3/273
For Service Engineer