Table 2-6 2-Way Circuit Single Or Dual Line Roll With Ent-Bulkroll; Table 2-7 2-Way Circuit Single Or Dual Bulk Roll With Ent-Bulkroll - Cisco ONS 15454 Reference Manual

Chapter 2 Procedures and Provisioning
ENT-BULKROLL-<OCN_TYPE>:[<TID>]:<FROM>:<CTAG>:::RTOSTART=<RTOSTART>,
•
[RFROMSTART=<RFROMSTART>],[RFROMEND=<RFROMEND>],RMODE=<RMODE>,
[CMDMDE=<CMDMDE>];
Choose which type of roll you want to perform and enter the corresponding command:
Step 1
For automatic rolling onto the same facility, but different STS (path roll):
•
Input Example:
ENT-ROLL-STS1:CISCO:STS-1-1-1,STS-2-1-1:1:::RFROM=STS-2-1-1,
RTO=STS-3-1-1,RMODE=AUTO,CMDMDE=FRCD;
For manual rolling onto the same facility, but different STS (path roll):
•
Input Example:
ENT-ROLL-STS1:CISCO:STS-1-1-1,STS-2-1-1:1:::RFROM=STS-2-1-1,
RTO=STS-3-1-1,RMODE=MAN,CMDMDE=FRCD;
For rolling onto a different facility with the same or different STS (line roll):
•
Input Example:
ENT-BULKROLL-OC48:CISCO:FAC-5-1:123:::RFROMSTART=STS-5-1-1,
RTOSTART=STS-6-1-1,RMODE=AUTO,CMDMDE=FRCD;
This command will roll all the STS and VT paths to a facility on Slot 6 with the same STS as shown
in
Table 2-6
Paths
STS#1
STS#2
VT#1 on STS#3
VT#2 on STS#3
STS#4
STS#5
VT#3 on STS#6
• For rolling a set of circuits onto a different facility (bulk roll):
Input Example:
ENT-BULKROLL-OC48:CISCO:FAC-5-1:123:::RFROMSTART=STS-5-1-1,
RTOSTART=STS-6-1-1,RFROMEND=STS-5-1-4,RMODE=AUTO,CMDMDE=FRCD;
This command will roll the paths shown in
Table 2-7
Paths
STS#1
STS#2
VT#1 on STS#3
Table 2-6.
2-Way Circuit Single or Dual Line Roll with ENT-BULKROLL
Before Roll
STS-5-1-1
STS-5-1-2
VT1-5-1-3-1-1
VT1-5-1-3-2-4
STS-5-1-4
STS-5-1-5
VT1-5-1-6-1-1
2-Way Circuit Single or Dual Bulk Roll with ENT-BULKROLL
Before Roll
STS-5-1-1
STS-5-1-2
VT1-5-1-3-1-1
2.8.3 2-Way Circuit Single Roll and Dual Roll Procedures
After Roll
STS-6-1-1
STS-6-1-2
VT1-6-1-3-1-1
VT1-6-1-3-2-4
STS-6-1-4
STS-6-1-5
VT1-6-1-6-1-1
Table 2-7.
After Roll
STS-6-1-1
STS-6-1-2
VT1-6-1-3-1-1
Cisco ONS SONET TL1 Command Guide, R6.0
2-55