Client Port Of Dwdm Cards; Och Port Of The Dwdm Card; Rules For Framing Type Autoprovisioning In Ctc Versus Tl1 - Cisco ONS 15454 Reference Manual

2.11 Rules for Framing Type Autoprovisioning in CTC Versus TL1

2.10.13.1 Client Port of DWDM Cards

When the client port of a DWDM card is provisioned as
1GFC/2GFC/10GFC/1GFICON/2GFICON/GIGE/10GIGE, the applicable PM for the client port
includes both the RMON-managed PM and the SONET PM. Therefore, the behavior of the
RTRV-PM-MMOD2>, INIT-REG-<MOD2>, and SCHED-PMREPT-<MOD2> commands is different
from the Ethernet or Fibre Channel port of the other cards where only RMON PM is applicable. The
differences include:
•
•
•
•
•

2.10.13.2 OCH Port of the DWDM Card

The OCH port of the TXP_MR_10G and TXP_MR_10E cards include the RMON-managed 8B10B PM
as well as the other SONET PM when their client port is provisioned as GIGE/10GIGE or
1GFC/2GFC/10GFC.
The RTRV-PM-OCH, INIT-REG-OCH, SCHED-PMREPT-OCH and REPT PM OCH commands have
similar behaviors as mentioned in the
2.11 Rules for Framing Type Autoprovisioning in CTC Versus TL1
The DS3/DS3E/DS3XM/DS3I/DS1cards can autosense framing and set the format accordingly;
however, this framing autosense feature can only be set using CTC. Use CTC to set the FMT attribute
on DS3/DS3E/DS3XM/DS3I/DS1cards to autoprovision. The FMT field will blank out for a few seconds
while the card is determining the framing mode received by that particular port. The FMT field is set
accordingly to unframed, M23, or CBit. If the card is not present (preprovisioned), setting the FMT field
to autoprovision will result in the FMT field defaulting to unframed.
Cisco ONS SONET TL1 Command Guide, R6.0
2-68
LOCN and DIRN parameters are applicable to the RTRV-PM-<MOD2>, INIT-REG-<MOD2>, and
SCHED-PMREPT-<MOD2> commands because they are applicable to the SONET optics PM.
When the LOCN or DIRN parameter is specified it would only apply to the SONET optics PM.
Because 1-MIN, 1-HR, or RAW-DATA are not applicable to the SONET optics PM, no SONET
optics PM would be returned in the output of RTRV-PM. If RAW-DATA is specified in the input of
the INIT-REG command, no SONET optics PM counter will be cleared.
When the accumulation time period is specified as 15-MIN or 1-DAY and the PM history bucket is
specified as 0 (current bucket), only the SONET optics PM will be returned in the output of the
RTRV-PM command. No RMON-managed PM will be included in the output of the RTRV-PM
command because RMON PM does not have current bucket.
A SONET optics PM montype cannot be specified in the input of the INIT-REG command only the
SONET optics PM counters will be cleared. When the ALL montype is specified, both the RMON
and the SONET optics PM counters will be cleared.
The commands used to manage RMON thresholds (ENT-RMONTH, DLT-RMONTH, and
RTRV-RMONTH) are only applicable to the RMON PM of the client port. The SONET optics PM
thresholds of the client port are still managed by the SET-TH and RTRV-TH commands. For
example, if the client port type of an MXP_MR_2.5G card is provisioned as GIGE, the following
commands would be used to create an RMON threshold:
ENT-RMONTH-GIGE::FAC-2-1-1:1::IFINOTETS,,,,1000:RISE=1000,FALL=900;
And the following command would be used to set the SONET optics PM threshold:
SET-TH-GIGE::FAC-2-1-1:1LBCL-MIN,0.2;
"2.10.13.1 Client Port of DWDM Cards" section on page
Chapter 2 Procedures and Provisioning
2-68.