Reel Bearing Adjustment (Cutting Units With Painted Side Plates) - Toro Reelmaster 7000-D Service Manual

Reel Bearing Adjustment (cutting units with painted side plates)

NOTE: Cutting units that have aluminum side plates do
not require reel bearing adjustment.
To insure cut quality and long life of the cutting reel bear-
ings, periodically check reel bearing adjustment.
Check Reel Bearing Adjustment
1. Remove hydraulic reel motor from cutting unit (see
Hydraulic Reel Motor Removal in the Service and Re-
pairs section of this chapter).
2. Loosen bedknife to reel adjustment until no contact
exists (see cutting unit Operator's Manual).
CAUTION
Contact with the reel, bedknife or other cutting
unit parts can result in personal injury. Use
heavy gloves when handling the cutting reel.
3. Hold on to the reel shaft and try to move the reel as-
sembly side to side. If reel end play exists, side to side
movement will be detected.
4. Using a suitable torque wrench and spline insert tool
(see Special Tools in this chapter), measure the rolling
resistance of the cutting reel. Cutting reel rolling torque
should not exceed 10 in- -lb (1.1 N- -m).
5. If reel has end play or if rolling torque is incorrect, per-
form reel bearing adjustment (see below).
6. After checking or adjusting reel bearings, adjust cut-
ting unit (see cutting unit Operator's Manual).
7. Install hydraulic reel motor to cutting unit (see Hy-
draulic Reel Motor Installation in the Service and Re-
pairs section of this chapter).
Reel Bearing Adjustment (Fig. 17)
1. Make sure that no contact exists between bedknife
and reel.
2. Remove cutting unit components on LH side plate to
allow access to bearing adjuster nut. If cutting unit is
equipped with an optional groomer or rear roller brush,
remove components for those options from left hand
side plate of cutting unit. See Service and Repairs sec-
tion of Chapter 10 -- Belt Driven Groomer for information
on groomer. See Rear Roller Brush in the Service and
Repairs section of this chapter for information on rear
roller brush.
Reelmaster 7000--D
15 to 17 in- -lb
(1.7 to 1.9 N- -m)
3
1. LH side plate
2. Threaded insert
3. Loosen set screw that secures bearing adjuster nut
in LH side plate of cutting unit.
IMPORTANT: Over tightening reel bearing adjuster
nut may damage reel bearings.
4. With the cutting unit and reel in a horizontal position,
use a 1 3/8" socket and torque wrench to over tighten the
bearing adjuster nut to 40 to 45 in- -lb (4.5 to 5.1 N- -m).
5. Loosen the bearing adjuster nut and then torque
bearing adjuster nut from 15 to 17 in- -lb (1.7 to 1.9
N- -m).
6. Using a suitable torque wrench and spline insert tool
(see Special Tools), check that reel rolling torque does
not exceed 10 in- -lb (1.1 N- -m). Also, check if reel bear-
ing endplay exists. If endplay exists after bearing adjust-
er nut is properly torqued, replace the cutting reel
bearings and seals (see Reel Assembly and Reel As-
sembly Service in the Service and Repairs section of
this chapter).
7. Apply Loctite #243 (or equivalent) to threads of set
screw and secure bearing adjuster nut in place with set
screw. Torque set screw from 12 to 15 in- -lb (1.4 to 1.7
N- -m).
8. After reel bearing adjustment, install all removed cut-
ting unit components or accessories.
Page 9 - - 13
4
12 to 15 in- -lb
(1.4 to 1.7 N- -m)
1
2
Figure 17
3. Bearing adjuster nut
4. Set screw
DPA Cutting Units