Mitsubishi Electric FR-A820-00046 (0.4K) Instruction Manual page 195

Pr.
Pr.
group
1480 H520
1481 H521
1482 H522
1483 H523
1484 H524
1485 H525
1486 H526
1487 H527
1488 H531
1489 H532
1490 H533
1491 H534
1492 H535
— 1499 E415
Pr.CLR
ALL.CL
Err.CL
— Pr.CPY
— Pr.CHG
— IPM
— AUTO
— Pr.MD
*1 Differs according to the capacity.
6%: FR-A820-00077(0.75K) or lower, FR-A840-00038(0.75K) or lower
4%: FR-A820-00105(1.5K) to FR-A820-00250(3.7K), FR-A840-00052(1.5K) to FR-A840-00126(3.7K)
3%: FR-A820-00340(5.5K), FR-A820-00490(7.5K), FR-A840-00170(5.5K), FR-A840-00250(7.5K)
2%: FR-A820-00630(11K) to FR-A820-03160(55K), FR-A840-00310(11K) to FR-A840-01800(55K)
1%: FR-A820-03800(75K) or higher, FR-A840-02160(75K) or higher
*2 The setting range or initial value for the FR-A820-03160(55K) or lower and FR-A840-01800(55K) or lower.
*3 The setting range or initial value for the FR-A820-03800(75K) or higher and FR-A840-02160(75K) or higher.
*4 The initial value for the FR-A820-00490(7.5K) or lower and FR-A840-00250(7.5K) or lower.
*5 Initial value for the FR-A820-00630(11K) or higher and FR-A840-00310(11K) and higher.
*6 Differs according to the capacity.
4%: FR-A820-00490(7.5K) or lower, FR-A840-00250(7.5K) or lower
2%: FR-A820-00630(11K) to FR-A820-03160(55K), FR-A840-00310(11K) to FR-A840-01800(55K)
1%: FR-A820-03800(75K) or higher, FR-A840-02160(75K) or higher
*7 The value for the 200 V class.
*8 The value for the 400 V class.
*9 The setting is available only when a plug-in option that supports Vector control is installed. For the corresponding parameters of each option, refer
to the detail page.
*10 The parameter number in parentheses is that used (displayed) on the LCD operation panel and the parameter unit.
*11 The setting range or initial value for the standard model.
*12 The setting range or initial value for the separated converter type.
*13 The setting range or initial value for the IP55 compatible model.
*14 The setting is available only for standard models.
*15 The setting is available only for standard models and IP55 compatible models.
*16 The setting is available when the PLC function is enabled.
*17 The setting is available only for the FR-A800-GF or when a compatible plug-in option is installed.
194
5. PARAMETERS
5.1 Parameter list
Name
Load characteristics
measurement mode
Load characteristics load
reference 1
Load characteristics load
reference 2
Load characteristics load
reference 3
Load characteristics load
reference 4
Load characteristics load
reference 5
Load characteristics
maximum frequency
Load characteristics
minimum frequency
Upper limit warning
detection width
Lower limit warning
detection width
Upper limit fault detection
width
Lower limit fault detection
width
Load status detection
signal delay time / load
reference measurement
waiting time
Parameter for manufacturer setting. Do not set.
Parameter clear
All parameter clear
Fault history clear
Parameter copy
Initial value change list
IPM initialization
Automatic parameter
setting
Group parameter setting
Minimum
Setting range setting
increments
0, 1 (2 to 5, 81 to 85) 1
0 to 400%, 8888, 9999 0.1%
0 to 400%, 8888, 9999 0.1%
0 to 400%, 8888, 9999 0.1%
0 to 400%, 8888, 9999 0.1%
0 to 400%, 8888, 9999 0.1%
0 to 590 Hz 0.01 Hz
0 to 590 Hz 0.01 Hz
0 to 400%, 9999 0.1%
0 to 400%, 9999 0.1%
0 to 400%, 9999 0.1%
0 to 400%, 9999 0.1%
0 to 60 s 0.1 s
(0), 1 1
(0), 1 1
(0), 1 1
(0), 1 to 3 1
— 1
0, 3003 1
— —
(0), 1, 2 1
Initial value
Refer to Customer
page setting
FM CA
0 417
9999 417
9999 417
9999 417
9999 417
9999 417
60 Hz 50 Hz 417
6 Hz 417
20% 417
20% 417
9999 417
9999 417
1 s 417
0 707
0 707
0 740
0 708
0 715
0 224
— 333
0 195