C.3 Node Default Settings - Cisco 15454-DS1-14= - 1.544Mbps Expansion Module Reference Manual

Appendix C Network Element Defaults
Table C-20 MRC-2.5G-4 Card Default Settings (continued)
Default Name
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.15min.PJCDIFF
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.15min.PJCS-PDET
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.15min.PJCS-PGEN
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.15min.PPJC-PDET
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.15min.PPJC-PGEN
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.15min.SES
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.15min.UAS
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.1day.CV
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.1day.ES
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.1day.FC
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.1day.NPJC-PDET
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.1day.NPJC-PGEN
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.1day.PJCDIFF
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.1day.PJCS-PDET
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.1day.PJCS-PGEN
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.1day.PPJC-PDET
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.1day.PPJC-PGEN
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.1day.SES
MRC25G-4.OC48-PORT.pmthresholds.sts3c-9c.nearend.1day.UAS

C.3 Node Default Settings

Table C-21 on page C-101
the following user-configurable defaults for each Cisco ONS 15454 node:
•
•
78-18106-01
lists the node-level default settings for the Cisco ONS 15454. Cisco provides
Circuit settings—Set the administrative state and path protection circuit defaults, and whether to
have circuits send a payload defect indication condition (PDIP).
General settings—Set general node management defaults, including whether to use Daylight
Savings Time (DST), whether to insert Alarm Indication Signal VT (AIS-V) in each VT when the
carrying STS crosses the signal degrade (SD) path bit error rate (BER) threshold, the IP address of
the Network Time Protocol/Simple Network Time Protocol (NTP/SNTP) server to be used, the time
zone where the node is located, the SD path BER value, the defaults description, whether to raise a
condition on an empty card slot, whether automatic autonomous Transcation Language One (TL1)
reporting of PM data is enabled for cross-connect paths on the node, whether or not to allow ports
C.3 Node Default Settings
Default Value Default Domain
60 (count) 0 - 14400000
100 0 - 900
(seconds)
100 0 - 900
(seconds)
60 (count) 0 - 7200000
60 (count) 0 - 7200000
3 (seconds) 0 - 900
10 (seconds) 0 - 900
250 (B3 0 - 207360000
count)
200 0 - 86400
(seconds)
40 (count) 0 - 6912
5760 (count) 0 - 691200000
5760 (count) 0 - 691200000
5760 (count) 0 - 1382400000
9600 0 - 86400
(seconds)
9600 0 - 86400
(seconds)
5760 (count) 0 - 691200000
5760 (count) 0 - 691200000
7 (seconds) 0 - 86400
10 (seconds) 0 - 86400
Cisco ONS 15454 Reference Manual, R8.5
C-99