Toro Greensmaster eFlex 1021 Service Manual page 74

Assembling the Transmission Gear Box Assembly
Traction and Reel Drive Systems: Service and Repairs
1. Use a press to install the spacer (item 13 in
(12 and 25) into the transmission housing (26).
2. Install the retaining ring (item 5 in
(26).
3. Install the new grease seal (item 11 in
housing (26). Ensure that the seal lip is orientated toward the center of the
transmission housing. Press the seal into the transmission housing bore so
that the seal is flush to the edge of the transmission housing.
4. Install the new oil seal (item 6 in
Ensure that the seal lip is orientated toward the center of the transmission
housing. Press the seal into the transmission housing bore so that the seal
is flush to the edge of the transmission housing.
5. Install the new oil seal (item 14 in
Ensure that the seal lip is orientated toward the center of the transmission
housing. Press the seal into the transmission housing bore so that the seal
is flush to the edge of the transmission housing.
6. Press the flange bushings (item 7 in
(26).
7. Insert the sleeve bushing (Item 16 in
(26) until the sleeve bushing is flush with the transmission housing.
8. Press the oil seal (item 15 in
Ensure that the oil seal lip is orientated toward the center of the transmission
housing.
9. Apply a coat of grease to the O-ring seal (item 18 in
the groove of the traction selector shaft (19).
10. Insert the straight bushings (item 4 in
housing (26). Press the straight bushings into the transmission housing bore
so that the bushings are recessed from the edge of the transmission housing.
11. Apply a coat of grease to the O-ring (item 18 in
traction selector shaft (item 19 in
(item 19 in Figure 24) into the transmission housing (26).
12. Apply a coat of a grease to the O-ring (item 3 in
groove of the traction selector shaft (19). Slide the spacer bushing (2) onto
the traction selector shaft (19) and secure with a retaining ring (1).
13. Install the groomer pin (item 20 in
(19).
14. Install the detent ball (item 10 in
into the transmission housing assembly (26).
15. Insert the input shaft (item 19 in
assembly (20) and secure with the thin lock nut (18). Torque tighten the thin
lock nut to 47.5 to 61 N∙m (35 to 45 ft-lbs).
16. Use a press to install the 2 new ball bearings (item 6 in
spur gear (17) and secure with the 2 retaining rings (5).
17. Apply a coat of grease to the O-ring (item 2 in
O-ring onto the short bearing pin (1). Install the spur gear assembly (17) and
bearing spacer (4) onto the transmission housing assembly (20) and secure
with the short bearing pin and nut (8).
18. Use a press to install the 3 new ball bearings (item 6 in
spur gear (7) and secure with the 2 retaining rings (5).
Figure 24) into the transmission housing
Figure
Figure 24) into the transmission housing.
Figure 24) into the transmission housing.
Figure
Figure
Figure 24) into the transmission housing (26).
Figure
Figure 24). Insert the traction selector shaft
Figure 24) onto the traction selector shaft
Figure 24), detent spring (9) and plug (8)
Figure 26) into the transmission housing
Page 4–28
Figure 24) and new ball bearings
24) into the transmission
24) into the transmission housing
24) into the transmission housing
Figure 24) and slide onto
24) into the transmission
Figure 24) and slide onto the
Figure 24) and slide onto the
Figure 26) into the
Figure 26) and slide the
Figure 26) into the
Greensmaster
20248SL Rev A
® eFlex 1021