Cisco TelePresence Administrator's Manual page 454

Reference material
Command reference — xConfiguration
Zones LocalZone SubZones SubZone [1..1000] Bandwidth PerCall Inter Mode: <Limited/Unlimited/NoBandwidth>
Determines whether there is a limit on the bandwidth for any one call to or from an endpoint in this subzone. Default: Unlimited.
NoBandwidth: no bandwidth available. No calls can be made to or from this subzone.
Example: xConfiguration Zones LocalZone SubZones SubZone 1 Bandwidth PerCall Inter Mode: Limited
Zones LocalZone SubZones SubZone [1..1000] Bandwidth PerCall Intra Limit: <1..100000000>
The bandwidth limit (in kbps) for any one call between two endpoints within this subzone (applies only if the mode is set to Limited).
Default: 1920.
Example: Zones LocalZone SubZones SubZone 1 Bandwidth PerCall Intra Limit: 1920
Zones LocalZone SubZones SubZone [1..1000] Bandwidth PerCall Intra Mode: <Limited/Unlimited/NoBandwidth>
Determines whether there is a limit on the bandwidth for any one call between two endpoints within this subzone. Default: Unlimited.
NoBandwidth: no bandwidth available. No calls can be made within this subzone.
Example: xConfiguration Zones LocalZone SubZones SubZone 1 Bandwidth PerCall Intra Mode: Limited
Zones LocalZone SubZones SubZone [1..1000] Bandwidth Total Limit: <1..100000000>
Sets the total bandwidth limit (in kbps) of this subzone (applies only if the mode is set to Limited). Default: 500000.
Example: xConfiguration Zones LocalZone SubZones SubZone 1 Bandwidth Total Limit: 500000
Zones LocalZone SubZones SubZone [1..1000] Bandwidth Total Mode: <Limited/Unlimited/NoBandwidth>
Controls if this subzone has a limit on the total bandwidth of calls being used by its endpoints at any one time. Default: Unlimited.
NoBandwidth: no bandwidth available. No calls can be made to, from, or within this subzone.
Example: xConfiguration Zones LocalZone SubZones SubZone 1 Bandwidth Total Mode: Limited
Zones LocalZone SubZones SubZone [1..1000] Name: <S: 0, 50>
Assigns a name to this subzone.
Example: xConfiguration Zones LocalZone SubZones SubZone 1 Name: "BranchOffice"
Zones LocalZone SubZones SubZone [1..1000] Registrations: <Allow/Deny>
Controls whether registrations assigned to this subzone are accepted. Default: Allow.
Example: xConfiguration Zones LocalZone SubZones SubZone 1 Registrations: Allow
Zones LocalZone SubZones SubZone [1..1000] SIP Media Encryption Mode: <Off/On/BestEffort/Auto>
The media encryption policy applied by the VCS for SIP calls (including interworked calls) to and from this subzone. Default: Auto
On: All media must be encrypted.
Off: All media must be unencrypted.
BestEffort: Use encryption if available otherwise fallback to unencrypted media.
Auto: No media encryption policy is applied.
Example: xConfiguration Zones LocalZone SubZones SubZone 1 SIP Media Encryption Mode: Auto
Zones LocalZone Traversal H323 Assent Mode: <On/Off>
Determines whether or not H.323 calls using Assent mode for firewall traversal will be allowed. Applies to traversal-enabled
endpoints registered directly with the VCS. Default: On .
Example: xConfiguration Zones LocalZone Traversal H323 Assent Mode: On
Zones LocalZone Traversal H323 H46018 Mode: <On/Off>
Controls whether H.323 calls using H460.18 mode for firewall traversal are allowed. Applies to traversal-enabled endpoints
registered directly with the VCS. Default: On .
Example: xConfiguration Zones LocalZone Traversal H323 H46018 Mode: On
Cisco VCS Administrator Guide (X8.1.1) Page 454 of 507