Taper Roller Bearing Preload Adjustment - Honda Prelude 1993 Service Manual

Differential {Automatic Transmissionl
Taper Roller Bearing Preload Adjustment
NOTE: lf the transmission housing, torque converter
housing, differential carrier, taper roller bearing. outer
race or thrust shim were replaced, the bearing preload
must be adjusted.
1 . R e m o v e t h e b e a r i n g o u t e r r a c e a n d t h r u s t s h i m
from the transmission housing by heating the hous-
ing to about 212"F (100'C) with a heat gun.
CAUTION;
. Do not h6at tha houling in oxcass ol 212'F
{100"c1.
. Roplaco thc tapsr rollor bearing when tho outer
race is to bs rgplacad.
. Do not uso a ghim on the torqug convsrt9r hou3-
ing sid6.
N O T E : L e t t h e t r a n s m i s s i o n h o u s i n g c o o l t o t h e
r o o m t e m p e r a t u r e b e f o r e a d j u s t i n g t h e b e a r i n g
preroao.
HEAT GUN
1 5 - 1 8
Select the thrust shim from the table below so that
their total thickness is 2.60 mm (0.102 in).
CAUTION: Do not use mor€ than two shims to
adiust tho bearing prelosd.
BEARING OUTER
RACE
THRUST SHIM
No. Part Numb6r Thickncss
41441 - PK4 - 000
2.20 mm (0.087 in)
B
4 1 4 4 2 - P K 4 - 0 0 0
2.25 mm (0.089 in)
4 1 4 4 3 - P K 4 - 0 0 0
2.30 mm (0.091 in)
D
4 1 4 4 4 - P K 4 - 0 0 0
2.35 mm (0.093 in)
E 4 1 4 4 5 - P K 4 - 0 0 0
2 . 4 0 m m ( 0 . 0 9 4 i n )
F
4 1 4 4 6 - P K 4 - 0 0 0
2.45 mm (0.096 in)
G 4 1 4 4 7 - P K 4 - 0 0 0
2.50 mm (0.098 in)
n
4 1 4 4 8 - P K 4 - 0 0 0
2 . 5 5 m m ( 0 . 1 0 0 i n )
4 1 4 4 9 - P K 4 - 0 0 0
2 . 6 0 m m ( 0 . 1 0 2 i n )
J
4 1 4 5 0 - P K 4 - 0 0 0
2 . 6 5 m m ( 0 . 1 0 1 i n l
K
4 1 4 5 1 - P K 4 - 0 0 0
2 . 7 0 m m ( 0 . 1 0 6 i n )
L 4 1 4 5 2 - P K 4 - 0 0 0
2 . 7 5 m m ( 0 . 1 0 8 i n )
M 4 1 4 5 3 - P K 4 - 0 0 0
2 . 8 0 m m ( 0 . 1 1 0 i n )
N
4 1 4 5 4 - P K 4 - 0 0 0 2 . 8 5 m m { 0 . 1 1 2 i n )
o
4 1 4 5 5 - P K 4 - 0 0 0
2 . 9 0 m m ( 0 . 1 1 4 i n l
4 1 4 5 6 - P K 4 - 0 0 0
2 . 9 5 m m ( 0 . 1 1 6 i n )
4 1 4 5 7 - P K 4 - 0 0 0
3 . 0 0 m m ( 0 . 1 ' 1 8 i n )
R 4 1 4 5 8 - P K 4 - 0 0 0
3 . 0 5 m m ( 0 . 1 2 0 i n )
* Standard shim