Nokia 7210 Configuration Manual page 145

7210 SAS-M, T, R6, R12, Mxp, Sx, S Basic System
Configuration Guide
3HE 17358 AAAB TQZZA
The boot loader continuously iterates over the previously mentioned ports,
sending out DHCP requests until the boot loader receives a response from the
host.
• When the chassis-role parameter for the node is set to standalone, DHCP
requests are sent out of the following ports:
- ports 1/1/27, 1/1/28 (10GE ports) and ports 1/1/1, 1/1/2 (1GE ports) on the
24-port 7210 SAS-Sx 1/10GE, 7210 SAS-S 1/10GE, and 7210 SAS-Mxp
variants
- ports 1/1/51, 1/1/52 (10GE ports) and ports 1/1/1, 1/1/2 (1GE ports) on the
48-port 7210 SAS-Sx/S 1/10GE, and 7210 SAS-S 1/10GE variants
- ports 1/1/67, 1/1/68 (100GE ports) and ports 1/1/1, 1/1/2 (10GE ports) on
the 7210 SAS-Sx 10/100GE 64SFP+ 4CFP4 variant
- ports 1/1/c3/1 and 1/1/c4/1, and 10 GE ports 1/1/1 and 1/1/2 on the
7210 SAS-Sx 10/100GE 64SFP+ 4QSFP28 variant
In addition, the boot loader will attempt to load the TiMOS image (both.tim) from
the local flash if autoinit fails (that is, no responses were received from the DHCP
server).
• When the node is shipped from the factory (with the chassis-role set to factory-
default) and powered up for the first time, the node sends out DHCP requests
on the following ports:
- 10GE ports 1/1/25, 1/1/26, 1/1/27, and 1/1/28 on the 24-port
7210 SAS-Sx 1/10GE, 7210 SAS-S 1/10GE, and 7210 SAS-Mxp
- 10GE ports 1/1/49, 1/1/50, 1/1/51 and 1/1/52 on the 48-port
7210 SAS-Sx 1/10GE and 7210 SAS-S 1/10GE
- the first two 1GE ports, 1/1/1 and 1/1/2, on all 7210 SAS-Sx/S 1/10GE and
7210 SAS-Mxp variants
On a 7210 SAS-Sx 10/100GE CFP4 platform shipped from the factory, the
DHCP requests are sent out of the first two 10GE ports (1/1/1 and 1/1/2) and all
100GE ports (1/1/65, 1/1/66, 1/1/67, and 1/1/68).
On a 7210 SAS-Sx 10/100GE 64SFP+ 4QSFP28 variant, the DHCP requests
are sent out of ports 1/1/c1/1, 1/1/c2/1, 1/1/c3/1, and 1/1/c4/1, and the first two
10 GE ports (1/1/1 and 1/1/2). To change this, connect to the console and modify
the chassis-role parameter value to either satellite or standalone, as required.
After the chassis-role parameter is updated, the node attempts autoinit to
retrieve the BOF.
Use subject to Terms available at: www.nokia.com
© 2021 Nokia.
Boot Options
145