Cisco 10000 Series Configuration Manual page 364

Index
framing 4-3, 6-5, 6-7, 7-5, 7-7, 8-2, 8-3, 12-2, 13-2, 14-2, 15-2,
15-13
idle character
4-3, 4-8, 6-7, 6-20, 7-7, 7-19, 8-3, 8-8, 15-2,
15-3
idle-character
15-13
idle pattern
4-3, 6-5, 7-5, 8-2
interface 10-3, 11-3
keepalive
4-3, 6-7, 7-7, 8-3, 12-2, 13-2, 14-2, 14-3
loopback
4-12, 4-16, 6-5, 6-6, 7-5, 7-6, 8-13, 10-4, 11-5, 12-2,
15-3, 15-14
mac-address
10-4, 11-4
mdl 15-3
mtu
4-3, 6-7, 7-7, 8-3, 12-2, 13-2, 14-2, 14-3
national bit
15-16
negotiation auto
10-3, 11-4
pos framing 12-4, 13-4, 14-7
privileged EXEC mode hw-module
scramble
4-3, 4-8, 8-3, 8-7, 12-2, 13-2, 14-2, 15-3, 15-16
show
version 1-2, 2-1, 3-2, 4-2, 5-2, 6-2, 7-2, 8-2, 9-2, 10-2,
11-2, 12-2, 13-2, 14-2, 15-2
show interface slot/subslot/port
shutdown
15-2, 15-3, 15-8
T1 clock source
4-3, 5-3, 5-5, 6-6, 7-6, 8-2
T1 framing 4-3, 6-6, 7-6, 8-2
t1 yellow
4-19, 8-16
committed access rate (CAR)
community list
18-6
configuration
controller mode
5-6, 5-10, 5-16
IOS global
5-6, 5-10
values
1-2, 2-2, 3-2, 6-4, 6-6, 7-4, 7-5, 7-6, 15-2
configure
serial interface
5-9, 5-11
configuring an E3 interface
configuring a T3 interface
connections
STS-1
6-8, 6-14, 7-8, 7-14
controller
e1
5-2
Cisco 10000 Series Router Line Card Configuaration Guide
IN-4
16-5
9-5, 10-3, 11-3
18-5
15-5
15-5
parameters 5-18
t1
5-4
controller command
4-20, 8-17
controller configuration mode
controller sonet command
crc command
4-3, 6-7, 7-7, 8-2, 12-2, 13-2, 14-2, 14-3
cyclical redundancy check command
See crc command
D
default
1-Port Gigabit Ethernet Half-Height line card
values 10-2
1-Port Gigabit Ethernet line card values
1-Port OC-12 Packet over SONET line card
values
13-2
1-Port OC-48/STM-16 Packet over SONET line card
SDCC values
14-2
1-Port OC-48/STM-16 Packet over SONET line card
values 14-2
24-Port Channelized E1/T1 line card values
4-Port Channelized T3 Half-Height line card
6-Port Channelized T3 line card values
6-Port OC-3/STM-1 Packet over SONET line card
values 12-2
8-Port Fast Ethernet Half-Height line card values
channelized OC-12 line card values
7-6
gigabit Ethernet (GE) line card values
modifying 12-2, 13-2, 14-2
OC-12 ATM line card values
description command
15-2, 15-3, 15-7, 15-10
DS0
components, configuring
DS3
interface configuration
dsu bandwidth command
7-18, 8-2, 8-4, 8-6, 15-2, 15-3, 15-11
dsu mode command 4-3, 4-7, 6-7, 6-19, 7-7, 7-18, 7-19, 8-2, 8-7,
15-2, 15-3, 15-10
8-9
14-4
11-2
5-2, 5-4
4-3
8-2
6-4, 6-6, 7-4, 7-5,
9-2, 10-2, 11-2
3-2
6-21, 7-21
15-4
4-3, 4-5, 4-7, 6-7, 6-9, 6-19, 7-7, 7-9,
OL-8834-04
9-2