Table of Contents
Advertisement
Code Description
4 =
2/
AI
JOYST
operation, as the reference source.
• See above (
5 =
3
,4
(
DI
U
D
R
(motor potentiometer control).
• Digital input
• Digital input
• A Stop command resets the reference to zero (the
"reset").
• Parameter 2205
of change.
6 =
3
,4
– Same as above (
DI
U
D
• A Stop command does not reset the reference to zero. The
reference is stored.
• When the drive restarts, the motor ramps up (at the selected
acceleration rate) to the stored reference.
7 =
5
,6
– Same as above (
DI
U
D
digital inputs used.
8 =
– Defines the fieldbus as the reference source.
COMM
9 =
+
COMM
AI
combination as the reference source. See
correction
10 =
COMM
AI
*
combination as the reference source. See
correction
11 =
3
,4
DI
U
D
• Changing the control source (
) does not copy the reference.
REM
12 =
3
,4
DI
U
D
• Changing the control source (
) does not copy the reference.
REM
• Stop command resets reference to zero.
13 =
5
,6
DI
U
D
• Changing the control source (
) does not copy the reference.
REM
14 =
1+
2 – Defines an analogue input 1 (
AI
AI
(
2) combination as the reference source. See
AI
reference correction
15 =
1 *
2 – Defines an analogue input 1 (
AI
AI
(
2) combination as the reference source. See
AI
reference correction
16 =
1-
2 – Defines an analogue input 1 (
AI
AI
(
2) combination as the reference source. See
AI
reference correction
17 =
1/
2 – Defines an analogue input 1 (
AI
AI
(
2) combination as the reference source. See
AI
reference correction
190
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
– Defines analogue input 2 (
1/
) description.
AI
JOYST
) – Defines digital inputs as the speed reference source
3 increases the speed (the
DI
4 decreases the speed (the
DI
ACCELER TIME
DI
DI
1 – Defines a fieldbus and analogue input 1 (
on page 191.
1 – Defines a fieldbus and analogue input 1 (
on page 191.
(
) – Same as
3
RNC
DI
(
) – Same as
3
NC
DI
U
(
) – Same as
3
NC
DI
U
on page 191.
on page 191.
on page 191.
on page 191.
ACH550-01 User's Manual
Range
2), configured for joystick
AI
stands for "up").
U
stands for "down").
D
2 controls the reference signal's rate
3
,4
(
)), except:
U
D
R
3
,4
), except that
U
D
DI
Analogue input reference
Analogue input reference
,4
(
) above, except that:
U
D
R
1 to
2,
2 to
EXT
EXT
EXT
,4
above, except that:
D
1 to
2,
2 to
EXT
EXT
EXT
,4
above, except that:
D
1 to
2,
2 to
EXT
EXT
EXT
1) and analogue input 2
AI
Analogue input
1) and analogue input 2
AI
Analogue input
1) and analogue input 2
AI
Analogue input
1) and analogue input 2
AI
Analogue input
Parameter listing and descriptions
stands for
R
5 and
6 are the
DI
1)
AI
1)
AI
1,
to
EXT
LOC
1,
to
EXT
LOC
1,
to
EXT
LOC
Advertisement
Table of Contents
