Coating Materials List - Komatsu PC200-8M0 Shop Manual

SEN06142-00

Coating materials list

a The recommended coating materials such as adhesives, liquid gaskets, and greases used for disas-
sembly and assembly are listed below.
a For coating materials not listed below, use the equivalent of products shown in this manual.
Cate- Komatsu
Part No.
gory code
LT-1A 790-129-9030
LT-1B 790-129-9050
LT-2 790-129-9040
790-129-9060
(Set of adhe-
LT-3
sive and hard-
LT-4 790-129-9040
Holtz
790-129-9120
MH 705
ThreeBond
790-129-9140
1735
Aron-alpha
790-129-9130
201
Loctite
79A-129-9110
648-50
LG-5 790-129-9080
LG-6 790-129-9160
LG-7 790-129-9170
LG-8
ThreeBond 419-15-18131
1207B
LG-9
ThreeBond 790-129-9310
1206D
4
50-100
Capacity
150 g
20 g Polyethylene
(2 pcs.)
Polyethylene
50 g
Adhesive:
1 kg
Hardener:
ener) 500 g
Polyethylene
250 g
75 g
Polyethylene
50 g
Polyethylene
2 g
Polyethylene
50 cc
Polyethylene
1 kg
200 g
1 kg
100 g
200 g
100 General information on disassembly and assembly
Container Main features and applications
q
Use to prevent rubber gaskets, rubber cushions,
Tube
and cork plugs from coming out.
q
Use for plastic (except polyethylene, polypropy-
lene, tetrafluoroethylene and vinyl chloride), rub-
container ber, metal, and non-metal parts which require
immediate and strong adhesion.
q
Features: Resistance to heat and chemicals.
q
container Use to fix and seal bolts and plugs.
Can q Use to bond and seal metal, glass and plastics.
q
Use to seal plugs for blank holes
container
q
Tube Heat-resistant seal used to repair engines.
q
Instantaneous adhesive.
q
Curing time: From 5 sec. to 3 min.
q
container Use mainly to bond metals, rubbers, plastics, and
woods.
q
Instantaneous adhesive.
q
Quick-curing type (max. strength is obtained after
container 30 minutes)
q
Use mainly to bond rubbers, plastics, and metals.
q
Features: Resistance to heat and chemicals.
q
Use for fitted portions subjected to high tempera-
container
ture.
q
Use to seal various threaded portions, pipe joints,
and flanges.
q
container Use to seal taper plugs, elbows, and nipples for
hydraulic piping.
q
Features: Silicon-based heat and cold-resistant
sealant.
Tube
q
Use to seal flange surfaces and threaded portions.
q
Use to seal oil pan, final drive case, etc.
q
Features: Silicon-based quick-curing sealant.
q
Tube Use to seal flywheel housing, intake manifold, oil
pan, thermostat housing, etc.
q
Features: Silicon-based, heat and cold-resistant,
Tube vibration-resistant, impact-resistant sealant.
q Use to seal transfer case, etc.
q
Use for rough surfaces such as the circle gear top
seal which is not clamped by bolts, gaps in the
Tube
weld which must be caulked, etc.
q
Can be coated with paint.
Coating materials list
(Rev. 2009.08)
PC200, 200LC, 220, 220LC-8M0
1