Mitsubishi Electric IQSS-R-E Reference Manual page 351

Panasonic Industrial Devices SUNX Co., Ltd.
Error code Error and cause
4805H The data backup/restoration
function was performed for the
device which is not supported by
the data backup/restoration
function of iQ Sensor Solution.
4805H The end unit is not recognized
because the end unit is not
attached to the sensor amplifier
properly.
E0C4H Data backup/restoration
function was performed for the
station sub-ID to which the
sensor amplifier is not
connected.
E0C5H Data backup failed because the
end unit is not attached to the
sensor amplifier properly.
E0C6H Data restoration failed because
the end unit is not attached to
the sensor amplifier properly or
the specified backup data is not
correct.
4805H The end unit is not recognized
because the end unit is not
attached to the sensor amplifier
properly.
E0C4H Data backup/restoration
function was performed for the
station sub-ID to which the
sensor amplifier is not
connected.
E0C5H Data backup failed because the
end unit is not attached to the
sensor amplifier properly.
E0C6H Data restoration failed because
the end unit is not attached to
the sensor amplifier properly or
the specified backup data is not
correct.
4805H The end unit is not recognized
because the end unit is not
attached to the sensor amplifier
properly.
E0C4H Data backup/restoration
function was performed for the
station sub-ID to which the
sensor amplifier is not
connected.
E0C5H Data backup failed because the
end unit is not attached to the
sensor amplifier properly.
E0C6H Data restoration failed because
the end unit is not attached to
the sensor amplifier properly or
the specified backup data is not
correct.
Corrective action
The data backup/restoration function is not supported by SC-
T1JA, SC-A01, and SC-A02.
Perform the data backup/restoration function for the device which
is supported by the data backup/restoration function of iQ Sensor
Solution.
Check if the end unit unconnected flag (for one-station occupied
operation: 15th bit of RWr0, for four-station occupied operation:
RX1F) is not set.
Check if the end unit is attached to the sensor amplifier properly.
Check that the sensor amplifier is connected properly, and
perform data backup/restoration function to the connected station
sub-ID.
Check if the end unit is attached to the sensor amplifier properly,
and perform data backup again.
Check if the end unit is attached to the sensor amplifier properly
or the specified backup data is correct. Then perform the data
restoration again.
Check if the end unit unconnected flag (for one-station occupied
operation: 15th bit of RWr0, for four-station occupied operation:
RX1F) is not set.
Check if the end unit is attached to the sensor amplifier properly.
Check that the sensor amplifier is connected properly, and
perform data backup/restoration function to the connected station
sub-ID.
Check if the end unit is attached to the sensor amplifier properly,
and perform data backup again.
Check if the end unit is attached to the sensor amplifier properly
or the specified backup data is correct. Then perform the data
restoration again.
Check if the end unit unconnected flag (for one-station occupied
operation: 15th bit of RWr0, for four-station occupied operation:
RX1F) is not set.
Check if the end unit is attached to the sensor amplifier properly.
Check that the sensor amplifier is connected properly, and
perform data backup/restoration function to the connected station
sub-ID.
Check if the end unit is attached to the sensor amplifier properly,
and perform data backup again.
Check if the end unit is attached to the sensor amplifier properly
or the specified backup data is correct. Then perform the data
restoration again.
Type/model name
■Analog input unit
• SC-T1JA
• SC-A01
• SC-A02
■Digital fiber sensor
• FX-301
• FX-305
• FX-501
• FX-502
■Digital laser sensor
• LS-403
■Head-separated dual display
digital pressure sensor
• DPS-401
• DPS-402
APPX
Appendix 5 Error Code List
A
349