Cisco AS5350XM Configuration Manual page 47

Verifying Basic Setup
Board Hardware Version 1.11, Item Number 800-6572289-01,
Board Revision 02, Serial Number JAB082904P4.
Processor 0x0, MAC Address badb.adba.d044
2 Gigabit Ethernet interfaces
6 Serial interfaces
648 terminal lines
1 Channelized T3 port
512K bytes of NVRAM.
125184K bytes of ATA External CompactFlash (Read/Write)
Because the gateway has never been configured, it cannot find a startup configuration file. Therefore,
Step 3
the software asks, "Would you like to enter the initial configuration dialog? [yes/no]"
Enter no. In this example, the Cisco IOS software is configured manually. The automatic setup script is
not used. Configuring the Cisco IOS software manually develops your expertise.
Enter yes to terminate autoinstall.
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: no
Would you like to terminate autoinstall? [yes]: yes
This example shows the LAN interfaces and the slots in which feature cards are not inserted. The
Step 4
universal port feature card (formerly called Nextport module) firmware version is displayed (version
1.1.6.81). The gateway attempts to switch to a better clock source but does not find a suitable source
because the T1 trunks are not yet configured.
00:00:03: %NP_MD-6-SLOT_INSERTED: Slot 1 (108 ports max) inserted
00:00:16: %CARRIER-3-NO_DFC: DFC is not present - DFC 3
00:00:16: %CARRIER-3-NO_DFC: DFC is not present - DFC 4
00:00:16: %CARRIER-3-NO_DFC: DFC is not present - DFC 5
00:00:16: %CARRIER-3-NO_DFC: DFC is not present - DFC 6
00:00:16: %CARRIER-3-NO_DFC: DFC is not present - DFC 7
00:00:19: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
00:00:19: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up
00:00:19: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
00:00:19: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed
state to up
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed
state to down
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to down
00:00:23: %NP_BS-6-MODULE_STARTED: NextPort module 1/0/0 Started - 1.1.6.81
00:00:26: %NP_BS-6-MODULE_STARTED: NextPort module 1/0/1 Started - 1.1.6.81
00:00:30: %NP_MD-6-MODULE_UP: NextPort module 1/0/0 up
00:00:30: %NP_BS-6-MODULE_STARTED: NextPort module 1/0/2 Started - 1.1.6.81
00:00:33: %NP_MD-6-MODULE_UP: NextPort module 1/0/1 up
00:00:37: %NP_MD-6-MODULE_UP: NextPort module 1/0/2 up
00:01:05: %LINK-5-CHANGED: Interface Serial0/0, changed state to administratively down
00:01:05: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to administratively
down
00:01:05: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to administratively
down
00:01:05: %LINK-5-CHANGED: Interface Serial0/1, changed state to administratively down
00:01:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed
state to down
00:01:10: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 5400 Software (C5400-JS-M), Version 12.3(14)T,
TAC:Home:SW:IOS:Specials for info
Copyright (c) 2004 by cisco Systems, Inc.
Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide
Analyzing the System Boot Dialog
RELEASE SOFTWARE (fc1)
3