Page 1 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide Release 12.4T Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883...
Page 2 OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
Page 3 Last updated: December 10, 2008 This document provides basic information about the command-line interface (CLI) in Cisco IOS and Cisco IOS XE software and how you can use some of the CLI features. This document contains the following sections: Initially Configuring a Device, page i •...
Page 4: Using The Cli
• Change the behavior of the port; for example, by adding a password or changing the timeout value. The AUX port on the Route Processor (RP) installed in a Cisco ASR1000 series router does not serve Note any useful customer purpose and should be accessed only under the advisement of a customer support representative.
Page 5 Using the Command-Line Interface in Cisco IOS and Cisco IOS XE Software Using the CLI Table 1 CLI Command Modes Command Access Method Prompt Exit Method Mode Usage Mode User EXEC Log in. Issue the logout or exit Change terminal Router>...
Page 6 Using the Command-Line Interface in Cisco IOS and Cisco IOS XE Software Using the CLI Table 1 CLI Command Modes (continued) Command Access Method Prompt Exit Method Mode Usage Mode ROM monitor From privileged EXEC Issue the continue Run as the default rommon # >...
Page 7 Using the Command-Line Interface in Cisco IOS and Cisco IOS XE Software Using the CLI EXEC commands are not saved when the software reboots. Commands that you issue in a configuration mode can be saved to the startup configuration. If you save the running configuration to the startup configuration, these commands will execute when the software is rebooted.
Page 8 Using the Command-Line Interface in Cisco IOS and Cisco IOS XE Software Using the CLI The following examples show how to use the help commands: help Router> help Help may be requested at any point in a command by entering a question mark '?'.
Page 9 Using the Command-Line Interface in Cisco IOS and Cisco IOS XE Software Using the CLI Table 3 CLI Syntax Conventions Symbol/Text Function Notes < > (angle brackets) Indicate that the option is an Sometimes arguments are displayed argument. without angle brackets.
Page 10 Using the Command-Line Interface in Cisco IOS and Cisco IOS XE Software Using the CLI Understanding Enable and Enable Secret Passwords Some privileged EXEC commands are used for actions that impact the system, and it is recommended that you set a password for these commands to prevent unauthorized use. Two types of passwords, enable (not encrypted) and enable secret (encrypted), can be set.
Page 11: Abbreviating Commands
Using the Command-Line Interface in Cisco IOS and Cisco IOS XE Software Using the CLI Press Ctrl-N or the down arrow key—Recalls the most recent commands in the history buffer after • they have been recalled using Ctrl-P or the up arrow key. Repeat the key sequence to recall successively more recent commands.
Page 12: Using The No And Default Forms Of Commands
A debug command produces extensive output that helps you troubleshoot problems in your network. These commands are available for many features and functions within Cisco IOS and Cisco IOS XE software. Some debug commands are debug all, debug aaa accounting, and debug mpls packets. To use debug commands during a Telnet session with a device, you must first enter the terminal monitor command.
Page 13 Using the Command-Line Interface in Cisco IOS and Cisco IOS XE Software Using the CLI To use one of these output modifiers, type the command followed by the pipe symbol (|), the modifier, and the regular expression that you want to search for or filter. A regular expression is a case-sensitive alphanumeric pattern.
Page 14: Additional Information
• “Using the Cisco IOS Command-Line Interface” section of the Cisco IOS Configuration Fundamentals Configuration Guide: http://www.cisco.com/en/US/docs/ios/fundamentals/configuration/guide/cf_cli-basics.html “Using Cisco IOS XE Software” chapter of the Cisco ASR1000 Series Aggregation Services Routers Software Configuration Guide: http://www.cisco.com/en/US/docs/routers/asr1000/configuration/guide/chassis/using_cli.html • Cisco Product Support Resources http://www.cisco.com/web/psa/products/index.html...
Page 15 CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access...
Page 16 Using the Command-Line Interface in Cisco IOS and Cisco IOS XE Software Additional Information...
Page 17 Audience The Cisco IOS documentation set is intended for users who configure and maintain Cisco networking devices (such as routers and switches) but who may not be familiar with the configuration and maintenance tasks, the relationship among tasks, or the Cisco IOS commands necessary to perform particular tasks.
Page 18: Typographic Conventions
Documentation Conventions Documentation Conventions In Cisco IOS documentation, the term router may be used to refer to various Cisco products; for example, routers, access servers, and switches. These and other networking devices that support Cisco IOS software are shown interchangeably in examples and are used only for illustrative purposes. An example that shows one product does not necessarily mean that other products are not supported.
Page 19 Documentation Organization This section describes the Cisco IOS documentation set, how it is organized, and how to access it on Cisco.com. Included are lists of configuration guides, command references, and supplementary references and resources that make up the documentation set. The following topics are included: Cisco IOS Documentation Set, page iv •...
Page 20 Feature Guides Cisco IOS features are documented in feature guides. Feature guides describe one feature or a group of related features that are supported on many different software releases and platforms. Your Cisco IOS software release or platform may not support all the features documented in a feature guide.
Page 21 Cisco IOS software and Cisco IOS XE software, for all releases. The configuration guides and command references support many different software releases and platforms. Your Cisco IOS software release or platform may not support all these technologies.
Page 22 About Cisco IOS and Cisco IOS XE Software Documentation Documentation Organization Table 1 Cisco IOS and Cisco IOS XE Configuration Guides and Command References (continued) Configuration Guide and Command Reference Titles Features/Protocols/Technologies Cisco IOS Bridging and IBM Networking Transparent and source-route transparent (SRT) bridging, •...
Page 23 About Cisco IOS and Cisco IOS XE Software Documentation Documentation Organization Table 1 Cisco IOS and Cisco IOS XE Configuration Guides and Command References (continued) Configuration Guide and Command Reference Titles Features/Protocols/Technologies Cisco IOS H.323 Configuration Guide Gatekeeper enhancements for managed voice services, Gatekeeper Transaction Message Protocol, gateway codec order preservation and shutdown control, H.323 dual tone...
Page 24 About Cisco IOS and Cisco IOS XE Software Documentation Documentation Organization Table 1 Cisco IOS and Cisco IOS XE Configuration Guides and Command References (continued) Configuration Guide and Command Reference Titles Features/Protocols/Technologies Cisco IOS IP Routing Protocols Configuration Guide Border Gateway Protocol (BGP), multiprotocol BGP,...
Page 25 About Cisco IOS and Cisco IOS XE Software Documentation Documentation Organization Table 1 Cisco IOS and Cisco IOS XE Configuration Guides and Command References (continued) Configuration Guide and Command Reference Titles Features/Protocols/Technologies Cisco IOS Multiprotocol Label Switching MPLS Label Distribution Protocol (LDP), MPLS Layer 2 VPNs,...
Page 26 About Cisco IOS and Cisco IOS XE Software Documentation Documentation Organization Table 1 Cisco IOS and Cisco IOS XE Configuration Guides and Command References (continued) Configuration Guide and Command Reference Titles Features/Protocols/Technologies Cisco IOS Service Selection Gateway Configuration Guide Subscriber authentication, service access, and accounting.
Page 27 • Cisco product security overview • Product alerts and field notices • • Technical assistance Cisco IOS technical documentation includes embedded feedback forms where you can rate documents and provide suggestions for improvement. Your feedback helps us improve our documentation.
Page 28 CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access...
Page 29 Basic Hardware Architecture The cards that reside in the Cisco AS5350XM and Cisco AS5400XM chassis are of two types: trunk Note feature cards, which provide an T1, E1, or channelized T3 interface, and universal port, dial-only, and voice feature cards, which host the universal digital signal processors (DSPs) that dynamically handle voice, dial, or fax calls.
Page 30 S0:1, S0:2… Modems TDM bus T1 controllers PRI lines PSTN POTS line BRI line Client Client Client ISDN modem router Legend = Synchronous PPP = Asynchronous PPP = Configuration template Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 31 The Cisco AS5350XM and Cisco AS5400XM universal gateways use a Class C Flash File Note System. IFS first appeared in Cisco IOS Releases 11.3 AA and 12.0. For more information about IFS, see the chapter “Using the Cisco IOS File System” in the Cisco IOS Configuration Fundamentals Configuration Guide for your software release.
Page 32 Directory of system:/ dr-x <no date> memory -rw- 5026 <no date> running-config dr-x <no date> ucode dr-x <no date> vfiles Note Remember to include the trailing colon ( ) in dir commands. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 33: Getting Help
It supports encryption technologies, but it is not user accessible. Exploring Cisco IOS Software This section describes what you need to know about the Cisco IOS software (the software that runs the gateway) before you configure the gateway using the CLI.
Page 34 Understanding Basic Hardware Architecture and Cisco IOS Software Exploring Cisco IOS Software The examples in this guide show prompts for either a Cisco AS5350XM or a Cisco AS5400XM Note universal gateway. However, regardless of the prompt or output shown, all examples apply to either type of gateway.
Page 35 T1 controller. Step 6 Displays the only command (timeslots) Router(config-controller)# ds0-group 1 ? timeslots List of timeslots in the ds0-group available in ds0-group 1. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 36: Undoing A Command Or Feature
Enter the copy running-config startup-config command to save your configuration changes to nonvolatile random-access memory (NVRAM) so that they are not lost if there is a system reload or power outage. For example: Router# copy running-config startup-config Building configuration... Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 37 Timesaver reload or power outage. Upgrading to a New Cisco IOS Release Obtain new Cisco IOS features and more stable code by upgrading to a new Cisco IOS release. Step 1 Display the contents of flash memory: Router# cd flash:...
Page 38 Jan 01 2000 00:59:10 c5350-js-mz.121-3.T.bin 32768000 bytes total (13041600 bytes free) For more information on deleting the image, see the Cisco IOS File System document, available online at http://www.cisco.com/univercd/cc/td/doc/product/software/ios113ed/113aa/113aa_2/allplats/ifs.htm Note The Cisco AS5350XM and Cisco AS5400XM universal gateways use a Class C Flash File System.
Page 39 Understanding Basic Hardware Architecture and Cisco IOS Software Upgrading to a New Cisco IOS Release Reload the Cisco AS5350XM or Cisco AS5400XM universal gateway to run the new image. If you Step 5 erased the old Cisco IOS image, make sure that the boot system flash oldiosname.bin command is not enabled and pointing to the old image filename;...
Page 40 If the configuration register does not have the Break Abort Effect bit set (mask 0x0100), then • disconnect the cable on the console port and either log in to the Cisco AS5350XM or Cisco AS5400XM universal gateway through the AUX port or telnet in through a VTY session.
Page 41 In this example, you are selecting the • readonly read-only ROM monitor image. One reason could be that the upgrade image has features or side effects you do not like. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 42: Where To Go Next
CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks;...
Page 43 SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.
Page 44 Understanding Basic Hardware Architecture and Cisco IOS Software Where to Go Next Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 45 The Cisco AS5350XM and AS5400XM universal gateway Ethernet ports are Gigabit Ethernet ports (labeled GE0 and GE1 on the chassis). The Cisco IOS firmware and software is designed so that configurations for Fast Ethernet will work on the Cisco AS5350XM and AS5400XM universal gateways without requiring any modification by the user.
Page 46 If you observe no messages on the console port, verify that the baud rate is configured correctly. The Note Cisco AS5350XM and Cisco AS5400XM console port can support a baud rate up to 115200. The following boot sequence occurs. Step numbers and comments are inserted in the example to describe the boot sequence.
Page 47 “Would you like to enter the initial configuration dialog? [yes/no]” Enter no. In this example, the Cisco IOS software is configured manually. The automatic setup script is not used. Configuring the Cisco IOS software manually develops your expertise.
Page 48 00:01:10: %TRUNK_CLOCK-6-BAD_CLOCKS: There are no good clocks in the system. Remain in HOLDOVER mode 00:01:10: %TRUNK_CLOCK-6-BAD_CLOCKS: There are no good clocks in the system. Remain in HOLDOVER mode Enter the show version command to check the system hardware, Cisco IOS image name, uptime, and Step 5 restart reason: Router> show version Cisco Internetwork Operating System Software IOS (tm) 5400 Software (C5400-JS-M), Version 12.3(14)T,...
Page 49 The gateway booted from this image location. System image file is..Checking the Initial Running Configuration The Cisco IOS software creates an initial running configuration. Inspect the configuration to get familiar with the default settings. User input is shown in boldface type. Router> enable...
Page 50 2000000 interface Async4/00 no ip address no ip route-cache interface Async4/01 no ip address no ip route-cache interface Async4/02 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 51 InOut scheduler allocate 10000 400 The Cisco AS5350XM or Cisco AS5400XM universal gateway displays every asynchronous interface it recognizes. Therefore, if your system has a large number of asynchronous interfaces, the running configuration will be very long. To aggregate the asynchronous interfaces, you must assign them to a group-async interface using the command group-range.
Page 52 To learn more about management information bases (MIBs), see the online references at Note http://www.cisco.com/univercd/cc/td/doc/product/software/. Select your Cisco IOS release and search under new feature documentation. Inspecting CPU Utilization Enter the show process cpu command and then the show process cpu history command to investigate high CPU utilization.
Page 53 11111 99999 33333 ***** ***** 0..5..1..1..2..2..3..3..4..4..5..5..CPU% per second (last 60 seconds) 9244444444444444444344444444443443444444444443444444424444 0..5..1..1..2..2..3..3..4..4..5..5..CPU% per minute (last 60 minutes) * = maximum CPU% # = average CPU% 4444444444444444444449444440 0..5..1..1..2..2..3..3..4..4..5..5..6..6..7. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 54 Slot 7 (CT3 DFC) AS5400# AS5400# AS5400# AS5400# AS5400#show health-monitor summ AS5400#show health-monitor summary ? Output modifiers <cr> The following example shows the display output of the show health-monitor summary command: Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 55 The following procedure shows an example of how to enable, disable, and show the results of a wedged interface output: Enable the Interface Queue Wedge Monitor. Step 1 AS5400# configure terminal Enter configuration commands, one per line. End with CNTL/Z. AS5400#(config)# interface-monitor enable AS5400#(config)# ^Z Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 56 00:39:15: %HHM-3-INTFWEDGE: GigabitEthernet0/0 Output Queue Wedged 00:39:18: %HHM-3-INTFWEDGE: GigabitEthernet0/1 Output Queue Wedged 00:39:39: %HHM-3-INTFWEDGE: Virtual-Access2 Output Queue Wedged 00:39:42: %HHM-3-INTFWEDGE: Virtual-Access3 Output Queue Wedged AS5400# AS5400# AS5400# Show wedge output. Step 8 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 57 AS5400#(config)# no interface-monitor enable AS5400#(config)# ^Z AS5400# AS5400# AS5400# Show the interface wedge process running again. (No process is running now.) Step 4 AS5400# show proc cpu | i Intf AS5400# AS5400# Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 58 • For additional basic configuration information, see the Cisco IOS Dial Technologies Configuration Guide and Cisco IOS Dial Technologies Command Reference publications for your Cisco IOS software release, available online at Cisco.com. For more advanced configuration topics, see the Cisco IOS software configuration guide, feature modules, and command reference publications that pertain to your Cisco IOS software release.
Page 59 CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks;...
Page 60 Verifying Basic Setup Where to Go Next Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 61 Basic Configuration Using the Command-Line Interface The information in this chapter applies to the Cisco AS5350XM and Cisco AS5400XM universal gateways. After you have verified your basic setup, you are ready to begin performing basic tasks that prepare your system for data call processing.
Page 62 Configuring the Hostname, Password, and Time Stamps The first configuration tasks you might want to execute are assign a hostname to your Cisco AS5350XM or Cisco AS5400XM, set an encrypted password, and turn on time stamps for these reasons: Assigning a hostname allows you to distinguish between different network devices.
Page 63 The login keyword authenticates EXEC shell users. Additionally, configure PPP authentication to use the local database if the session was not already authenticated by the login keyword. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 64 Basic Configuration Using the Command-Line Interface Configuring Local AAA Security AAA (called triple A) is the Cisco IOS security model used on all Cisco devices. AAA provides the primary framework through which you set up access control on the Cisco AS5350XM or Cisco AS5400XM universal gateway.
Page 65 Basic Configuration Using the Command-Line Interface Creating a Login Banner For comprehensive information about how to implement a Cisco AAA-based security environment for Note dial-based and router environments, see the Cisco AAA Implementation Case Study document, available online at http://www.cisco.com/univercd/cc/td/doc/cisintwk/intsolns/aaaisg/index.htm...
Page 66: Configuring The Asynchronous Group Interface
An 80 percent ping-success rate is normal for the first time you ping an external device. The Cisco AS5350XM and Cisco AS5400XM universal gateways do not have an Address Resolution Protocol (ARP) entry for the external device. A 100 percent success rate is achieved the next time you ping the device.
Page 67 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/32 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 86 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 68 Sent: 8891 packets, 222264 bytes, 0 dropped Configuring T1 and E1 Feature Cards On a Cisco AS5350XM or Cisco AS5400XM universal gateway, you can allocate the available channels for channelized T1 and E1 lines in the following ways: Configure all channels to support ISDN PRI.
Page 69 17-23 type e&m-fgb command. This is an unusual configuration because it requires you to align the correct range of timeslots on both ends of the connection. For configuration information about leased-line or nondial use, see the Cisco IOS Configuration Note Fundamentals Configuration Guide for your software release.
Page 70 For details on the TDM feature, see the Cisco IOS software configuration guide and Note command reference publications. These publications are available on the Documentation DVD and on the World Wide Web from the Cisco home page, or you can order printed copies. See “Obtaining Documentation” section on page If you are having trouble: First decide if the problem is due to the T1 or E1 line or with a particular channel group.
Page 71 AS5400(config-controller)# framing c-bit Step 5 Enters line clock source: internal or line. AS5400(config-controller)# clock source line Step 6 Enters your cable length: values range from 0 to AS5400(config-controller)# cablelength 450 450 feet. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 72: Configuring Isdn Pri
Channelized T1 ISDN PRI offers 23 B channels and 1 D channel. Channelized E1 ISDN PRI offers 30 B channels and 1 D channel. Channel 24 is the D channel for T1, and channel 16 is the D channel for Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 73 Basic Configuration Using the Command-Line Interface Configuring ISDN PRI For a complete description of the commands mentioned in this section, refer to the Cisco IOS Dial Technologies Command Reference for your software release. Request PRI Line and Switch Configuration from a Telco Service Provider Before configuring ISDN PRI on your Cisco router, you need to order a correctly provisioned ISDN PRI line from your telecommunications service provider.
Page 74 Defines the line code as binary 8 zero substitution AS5400(config-controller)# linecode b8zs (B8ZS) for the T1 or CT3 feature card. Defines the line code as high-density bipolar 3 AS5400(config-controller)# linecode hdb3 (HDB3) for the E1 feature card. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 75 This could indicate switch problems. AS5400# show controller t3 1/0 T3 1/0 is up. Applique type is Channelized T3 No alarms detected. MDL transmission is disabled Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 76 0 Active Layer 3 Call(s) Activated dsl 0 CCBs = 0 The Free Channel Mask: 0x807FFFFF ISDN Serial1/0:28:23 interface dsl 27, interface ISDN Switchtype = primary-5ess Layer 1 Status: ACTIVE Layer 2 Status: Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 77 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 2 2 2 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 78 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 2 2 2 Your Cisco AS5350XM or Cisco AS5400XM universal gateway supports a total of 248 ISDN channels Note per ingress trunk feature card.
Page 79 Trunks are selected based on the trunk that is least used (default configuration) or the hunt scheme configured. Using trunk groups simplifies the task of configuring dial peers and interfaces, and also enables the dynamic selection of interfaces as needed in the access server. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 80: Pri Trunk Configuration
Configure framing, clock source, DS0 group, and so forth. Step 1 AS5400(config)# controller T1 3 AS5400(config-controller)# framing esf AS5400(config-controller)# clock source line secondary 3 AS5400(config-controller)# linecode b8zs AS5400(config-controller)# pri-group timeslots 1-24 AS5400(config-controller)# ! Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 81 Pend = 0, Free = 23 advertise_flag 0x00000040, capacity timer 25 sec tripl_config_mask 0x00000000 AC_curr 24, FD_curr 0, SD_curr 0 succ_curr 0 tot_curr 0 succ_report 0 tot_report 0 changed 0 replacement position 0 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 82 The D channel notifies the central office switch to send the incoming call to particular time slots on the Cisco gateway or router. Each one of the B channels carries data or voice. The D channel carries signaling for the B channels. The D channel identifies whether the call is a circuit-switched digital call or an analog modem call.
Page 83 Output queue 0/40, 0 drops; input queue 0/75, 0 drops 1 minute input rate 0 bits/sec, 0 packets/sec 1 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 84 ISDN digital calls, V.110 data calls, and V.120 data calls. Modem pass-through calls are not included in dial services. One SPE provides services for six ports, with additional ports per SPE. Busyout and shutdown can be configured at the SPE or port level. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 85 SPE firmware is automatically downloaded to a universal port or dial-only feature card from the Cisco AS5350XM or Cisco AS5400XM universal gateway when you boot the system for the first time or when you insert a universal port or dial-only feature card while the system is operating. When you insert feature cards while the system is operating, the Cisco IOS image recognizes the feature cards and downloads the required firmware to the feature cards.
Page 86 Enters global configuration mode. You are in AS5400# configure terminal Enter configuration commands, one per line. global configuration mode when the prompt End with CNTL/Z. changes to AS5350(config)# AS5400(config)# AS5400(config)# Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 87 The modem speed 115200 bps and hardware flow control are the default settings for integrated modems. Resetting to Default Values for Country Codes To reset the modem to default settings for country codes, enter the no spe country command in global configuration mode. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 88 Special Chars: Escape Hold Stop Start Disconnect Activation none none Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch 00:10:00 never none not set Idle Session Disconnect Warning never Login-sequence User Response Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 89 Where slash marks appear in the command • syntax, they are required. Step 4 Specifies that the firmware is in flash memory and AS5400(config-voice-dsp)# firmware location flash:filename identifies the file name. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 90 4.4.5 system:/bundled_fw_image Configuring Clocking The time-division multiplexing (TDM) bus on the Cisco AS5350XM and Cisco AS5400XM universal gateway backplane can receive an input clock from one of these basic sources on the gateway: T1, E1, and CT3 feature cards •...
Page 91 1 and 99. Feature card slot is a value between 1 and 7. DS1 port number controller is a value between 0 and 7. DS1 port specifies T1 port. Note Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 92: Configuration Examples
T1 or E1): AS5400# show tdm clocks Primary Clock: -------------- TDM Bus Master Clock Generator State = HOLDOVER Backup clocks for primary: Source Slot Port DS3-Port Priority Status State Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 93 Verify your user-configured trunk clock selection using the show tdm clocks command: • AS5400# show tdm clocks Primary Clock: System primary is slot 2 port 0 of priority 15 TDM Bus Master Clock Generator State = NORMAL Backup clocks for primary: Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 94 Change the default setting for the dial-tdm-clock priority parameter from free-running clock to a setting that matches your system requirements. Enabling IP Basic Setup To fine-tune the IP routing functions and domain-name services for EXEC shell users, follow these steps: Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 95 The ip name-server command is used for mapping names to IP addresses. Testing Asynchronous Shell Connections This task verifies that the following components are working: The physical asynchronous data path • Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 96 Basic IP functionality to support shell sessions • The Cisco IOS software provides a command-line interface (CLI) called the EXEC that can be accessed by dialing in with a modem. The EXEC provides access to terminal-shell services (no PPP) to do the following: •...
Page 97 Integrated Modem Modem State: Ready Note The show caller command was added to the Cisco IOS software in Cisco IOS Release 11.3 AA and Release 12.0 T. If your software release does not support this command, use the show user command.
Page 98 0 crypto mib ipsec flowmib history tunnel size 200 crypto mib ipsec flowmib history failure size 200 controller T1 1/0 framing sf linecode ami controller T1 1/1 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 99 Async4/107 no ip address interface Group-Async0 no ip address no ip route-cache no ip mroute-cache no group-range ip classless ip route 0.0.0.0 0.0.0.0 172.21.101.1 no ip http server Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 100: Saving Configuration Changes
Chapter 6, “Managing and Troubleshooting the Voice Feature Card,” to configure, manage, and • troubleshoot voice feature card connections on your gateway. Appendix C, “Comprehensive Configuration Examples.” • Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 101 CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks;...
Page 102 Basic Configuration Using the Command-Line Interface Where to Go Next Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 103: Configuring Synchronous Serial Interfaces For Wan Support
Continuing Configuration Using the Command-Line Interface The information in this chapter applies to the Cisco AS5350XM and Cisco AS5400XM universal gateways. This chapter continues where the “Basic Configuration Using the Command-Line Interface” chapter ends. After you have commissioned your Cisco AS5350XM or Cisco AS5400XM universal gateway, you might want to configure other features that include serial interface support, T1 channel groups, and signaling.
Page 104 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 358 packets output, 25157 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 output buffer failures, 0 output buffers swapped out Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 105 The following example shows a T1 controller configured for channel groups and an ISDN PRI group. The pri-group command and the channel-group command cannot have overlapping time slots; note the correct time slot configuration. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 106 Group identifier number for the interface under control of this D channel • Note Your Cisco AS5350XM or Cisco AS5400XM universal gateway must connect to a Primary-4ESS, Primary-DMS 100, or Primary-NI switch (see Table 5 on page 15) and must also have a channelized T1 controller and, as a result, be ISDN PRI capable.
Page 107 There are 24 total available B channels. The primary D-channel is DSL 0 in state IN SERVICE. The backup D-channel is DSL 1 in state STANDBY. The current active layer 2 DSL is 0. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 108: Configuring E1 R2 Signaling
E1 interface to support different types of R2 signaling, used in older analog telephone networks. The Cisco implementation of R2 signaling has dialed number identification support (DNIS) turned on Note by default. If you enable the automatic number identification (ANI) option, the collection of DNIS information is still performed.
Page 109 SPE country command. On the Cisco AS5350XM and Note Cisco AS5400XM universal gateway, DS-0 companding law selection is configured for the entire system rather than on individual voice ports. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 110: Country Codes For R2 Signaling
Framing is CRC4, Line Code is HDB3, Clock Source is Line Primary. Data in current interval (785 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 111: Configuring Alarms
Fan failure Cisco IOS software polls every second to detect the failure events that you have configured and turns on an alarm when any one of the failure events is detected. By default, the facility alarm is off. Users have to configure a facility alarm command to enable monitoring of the failure conditions.
Page 112 Verify To see the status of the alarms, enter the show facility-alarm command: AS5350# show facility-alarm Device State ------ ----- gigabitethernet 0/0 UP Modem Card 4 Facility Alarm is ON Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 113 For additional basic configuration information, see the Cisco IOS Dial Technologies Configuration • Guide and Cisco IOS Dial Technologies Command Reference publications for your software release. For more advanced configuration topics, see the Cisco IOS software configuration guide, feature modules, and command reference publications that pertain to your Cisco IOS software release.
Page 114 CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks;...
Page 115 Cisco AS5350XM and Cisco AS5400XM universal gateway. Dial-only feature card—The dial-only feature card supports 60 (DL-60) to 108 (DL-108) dial calls • in a Cisco AS5350XM and Cisco AS5400XM universal gateway. It does not support voice or fax services. Note Dial services include modem calls (all modulations), ISDN digital calls, V.110 data calls, and V.120 data...
Page 116 You can use show port modem log or show port digital log to display specific service events, but you must use clear port log to clear the entire port log. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 117 Configuring SPE Performance Statistics Viewing SPE Performance Statistics You can view SPE statistics using the Cisco IOS software with the gateway. To view performance statistics for the universal port or dial-only feature cards, enter one or more of the following commands...
Page 118: Managing Ports
• slot, specified SPE, or specified SPE range. It is used in the same way as the show modem command is used for MICA modems. (The command is not supported on the Cisco AS5350XM or Cisco AS5400XM universal gateway.) show spe Commands show spe log—Displays the oldest event first from the slot history event log.
Page 119 This replaces the modem busyout command. Maintenance activities such as testing can still be performed while a port is in busyout mode. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 120 SPE firmware, performing busyout on SPEs, and clearing active calls on the SPEs. SPE Country On the Cisco AS5350XM and Cisco AS5400XM universal gateways, DS0 companding law selection is configured for the entire system rather than on individual voice ports.
Page 121 4/13 0078-0083 ACTIVE 0 ______ ______ 4/14 0084-0089 ACTIVE 0 ______ ______ 4/15 0090-0095 ACTIVE 0 ______ ______ 4/16 0096-0101 ACTIVE 0 ______ ______ 4/17 0102-0107 ACTIVE 0 ______ ______ Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 122: Troubleshooting
SPE, and configure a scheduled recovery of SPEs. Configure SPE Diagnostic Tests You can perform three types of diagnostic tests on your SPE modem: SPE startup test • SPE autotest • SPE back-to-back test • Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 123 2/6. Enter the following command in privileged EXEC mode (the prompt is displayed as AS5350# ) to perform internal back-to-back port tests between two ports: AS5400# Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 124 You can configure automatic recovery (removal from service and reloading of SPE firmware) of ports on an SPE at any available time from global configuration mode (the prompt is AS5350(config)# AS5400(config)# Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 125 You do not have to take any action to use the preinstalled version of SPE firmware with new systems. Note You can acquire new SPE firmware from the Cisco Software Center in one of two ways: Bundled in regular Cisco IOS releases. See the “Using SPE Firmware Bundled with Cisco IOS...
Page 126 Unbundled from Cisco.com. This is a more up-to-date version of SPE firmware released before the • next Cisco IOS release, or a special version of SPE firmware shipped with a new board. See the “Upgrading SPE Firmware from the Cisco.com FTP Server” section on page 13 for details.
Page 127 Note You must be a registered Cisco user to log in to the Cisco Software Center. You can download software from the Cisco.com FTP server using an Internet browser or using an FTP application. Both procedures are described. Using an Internet Browser Step 1 Launch an Internet browser.
Page 128 TFTP server that can be accessed by the universal gateway. Using an FTP Application The directory path leading to the SPE firmware files on cco.cisco.com is subject to change without Note notice. If you cannot access the files using an FTP application, try the Cisco Systems URL http://www.cisco.com/cgi-bin/ibld/all.pl?i=support&c=3...
Page 129 Specify a binary image transfer: ftp> binary 200 Type set to I. Copy the SPE firmware files from the gateway to your local environment with the get command. Step 6 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 130 Because the SPE firmware is configurable for individual SPEs or ranges of SPEs, the Cisco IOS software automatically copies the SPE firmware to each SPE each time the gateway restarts.
Page 131 Step 3 Note As explained previously, the version number and UPG firmware filename may not match until the upgrade is complete. AS5400# show spe version IOS-Bundled Default Firmware-Filename Version Firmware-Type Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 132 Specify when the SPE firmware upgrade is to occur. Step 7 AS5400(config-SPE)# firmware upgrade busyout | download-maintenance | reboot Type the exit command to exit SPE config mode. Step 8 AS5400(config-SPE)# exit Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 133 Use this procedure to update SPE firmware on the SPEs in your gateway if you decide to use the version of SPE firmware bundled with Cisco IOS software instead of the version already mapped to your ports. To set the SPE firmware mapping to the SPE firmware version bundled with Cisco IOS software, enter the following commands: Enter the enable command.
Page 134 CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks;...
Page 135 Any use of actual IP addresses in illustrative content is unintentional and coincidental. © 2006, 2009 Cisco Systems, Inc. All rights reserved. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 136 Managing and Troubleshooting the Universal Port and Dial-Only Feature Cards Where to Go Next Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 137 64 to 384 channels. The voice feature card converts voice and fax calls into IP packets or frames that can be transmitted as voice over IP (VoIP) over a variety of transport technologies on the Cisco AS5350XM or Cisco AS5400XM universal gateways.
Page 138 Viewing DSP Performance Statistics Viewing DSP Performance Statistics You can view DSP statistics by using the Cisco IOS software with the universal gateway. To view performance statistics for the voice feature cards, enter one or more of the following commands in privileged EXEC mode (at the prompt).
Page 139: Debugging Commands
Automatic recovery (removal from service and reloading of DSP firmware) is enabled by default for the voice feature card. You can disable automatic recovery using the voice dsp recovery disabled command in configuration mode. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 140 Unbundled from Cisco.com. This is a more up-to-date version of DSP firmware released before the • next Cisco IOS release, or a special version of DSP firmware shipped with a new board. See the “Using Unbundled DSP Firmware” section on page 5 for details.
Page 141 The copy ios-bundled command is not necessary with the voice feature card. By default, the version of Note DSP firmware bundled with the Cisco IOS software release is transferred to all DSPs that are not specifically configured for a different DSP firmware file.
Page 142 Type the exit command to exit DSP config mode. Step 8 AS5400(config-voicedsp)# exit AS5400(config)# Press the Enter key to make the changes, and then type Ctrl-Z to return to privileged EXEC mode. Step 9 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 143 (for example, the Cisco IOS software image). If the new Cisco IOS image contains the same DSP firmware as the old one, no new code is downloaded Note to the DSPs.
Page 144 You must buy a license to access the DSPWare that supports the AMR-NB codec. It is recommended that Note you purchase a Cisco SMARTnet contract in order to streamline the process of getting the AMR-NB codec DSPWare. When obtaining your license, use the following part numbers:...
Page 145 CMRs. The Cisco AS5400XM and Cisco AS5350XM cannot initiate CMRs and received CMRs can be processed. For more information about AMR-NB codecs, see RFC3267.
Page 146 CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks;...
Page 147 Managing and Troubleshooting the Voice Feature Card Where to Go Next Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 148 Managing and Troubleshooting the Voice Feature Card Where to Go Next Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 149 Managing and Troubleshooting the Voice Feature Card Where to Go Next Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 150 Managing and Troubleshooting the Voice Feature Card Where to Go Next Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 151 Configuring Voice over IP The information in this chapter applies to the Cisco AS5350XM and Cisco AS5400XM universal gateways. Voice over IP (VoIP) technology enables voice-capable routers and switches to transport packetized live voice traffic such as telephone calls over IP data intranetworks or internetworks rather than public switched telephone networks (PSTN) or private TDM (PBX) networks.
Page 152 Although VoIP technology is primarily software-based, it requires that you install a universal port or Note voice feature card into the appropriate slot of your Cisco AS5350XM or Cisco AS5400XM universal gateway. The number of ports or channels available for sending VoIP data depends on the capacity of your card.
Page 153: Call Flow
PBX at the destination that can complete the call). • Initiates H.323 session across network. • Processes voice signals and sends packets over network. As appropriate, sends call-progress and other in-band signals. Ends session. • Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 154 E.164 phone number of the associated endpoint, and data address is the address to which the gateway sends a call whose destination pattern matches the one in the peer. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 155: Matching Rules
Searches its POTS dial peers until it finds dial-peer 4, whose destination pattern matches the dialed digits. Sends the call out the port specified by that dial peer (port 1/0:3, which connects to extension 6000). Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 156 Make routing or dialing transparent to users by, for example, avoiding such inconveniences as • secondary dial tones. Contact your PBX vendor to learn how to reconfigure PBX interfaces. • Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 157 Configuring Basic VoIP Configure Signaling on Voice Ports The Cisco AS5350XM and Cisco AS5400XM universal gateways process and manage digital voice calls on the universal port or voice feature card. They support voice configuration on channelized T1, E1, and T3 trunk interfaces.
Page 158: Configurable Options
Prepends info digits to the calling number. info-digits Sets information type for dial peer. information-type Sets maximum connections per peer; “no” sets to unlimited. max-conn Negates a command or sets its defaults. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 159 Sets maximum redirects for this peer. max-redirects Negates a command or sets its defaults. Sets calling or called party numbering type. numbering-type Configures preference order of the peer. preference Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 160 For more information, see Voice over IP for the Cisco AS5300, available online at http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120t/120t3/voip5300/ Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 161 — — Consult the references at the end of the chapter before you create a dial-peer configuration table. See also Voice over IP for the Cisco AS5300, available online at http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120t/120t3/voip5300/ Configuring Echo Cancellation on the Voice Feature Card The echo-cancel enable command enables cancellation of voice that is sent out the interface and received back on the same interface;...
Page 162 Router(config-voiceport)# exit Configuring Nextport Echo Canceller Control (optional) The AS5350XM and AS5400XM universal gateways can detect 2100Hz tones, received in G.711 encoded VoIP packets. Customers can enable Nextport Voicecap to control the echo canceller when 2100-Hz tones are received in G.711 encoded VoIP packets from either the PSTN or IP side of the network.
Page 163 The Voicecap must be applied to the voice port. Note The Cisco IOS CLI show command does not display the current echo state. However, you can display the EST trace messages that show the tone detections and the resultant echo operations if you issue debug trace module f080 0010 x/y/z.
Page 164 : Session 0x0144 ECAN Is Disabled *Apr 26 21:40:51.739: 00:00:04: Port Trace Event: *Apr 26 21:40:51.739: Port : 3/00 *Apr 26 21:40:51.739: Address : 0x3000000 5350-torpedo#*Apr 26 21:40:51.739: Trace Event: 0x2 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 165 QoS features enable you to balance service levels for user satisfaction, granting priority service to voice while servicing data transmission to the degree of Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 166 Cisco IOS software provides many features for optimizing QoS. Fine-tuning your network to adequately support VoIP almost certainly involves enabling some of these features. Be sure to read the cited references as you enable features, because the details of wide-scale QoS deployment are beyond the scope of this document.
Page 167 Frame Relay IP RTP Priority (described in the third reference below). For more information and configuration options, see the following: VoIP over PPP Links with Quality of Service (LLQ / IP RTP Priority, LFI, cRTP), available online at • http://www.cisco.com/warp/public/788/voice-qos/voip-mlppp.html Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 168 Protocol) on all WAN links that transport voice traffic. Configure RSVP when you configure dial peers. Do not enable RSVP in conjunction with Frame Relay traffic shaping. For more information and configuration options, see Voice over IP for the Cisco AS5300, available online http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120t/120t3/voip5300/ Call-Admission Control You can gracefully prevent calls from entering your Cisco AS5350XM or Cisco AS5400XM universal gateway from the PSTN when certain resources—such as CPU, memory, and interfaces—are not...
Page 169 QoS features. See these references and the “Additional Resources” section for more information. Other Bandwidth-Reduction Features Voice Encoding The Cisco AS5350XM and Cisco AS5400XM universal gateways offer multiple codec (coders/decoder) methodologies for encoding (digitizing and, optionally, compressing) voice: G.711 • G.723.1 •...
Page 170 If your calls are subject to significant toll-office processing, choose PCM if you have sufficient bandwidth. We also recommend that you employ a Cisco IOS Multimedia Conference Manager (H.323 gatekeeper) or management application such as Cisco Voice Manager to help manage these types of processes.
Page 171: Additional Resources
Note that the trade-off for increasing jitter-buffer size is a corresponding increase in delay. Cisco jitter buffers are normally sized dynamically, and adaptive mode plus default buffer size should suffice, but you can adjust mode and size as needed.
Page 172 CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks;...
Page 173: Table Of Contents
Finding Feature Information in This Module Your Cisco IOS software release may not support all of the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To...
Page 174: Prerequisites For Voice Enhancement Features For Cisco Ios Release 12.4(24)T
The prerequisites defined in the following sections apply to the configuration of the Cisco VGD 1T3, Cisco AS5350XM, and Cisco AS5400XM voice gateways: • You must have Cisco IOS Release 12.4(24)T or a later release installed on the Cisco VGD 1T3, Cisco AS5350XM, and Cisco AS5400XM voice gateways. •...
Page 175: Information About Voice Enhancement Features For Cisco Ios Release 12.4(24)T
(TTS) technology to make reservations, verify shipments, or order products. To enable the media forking feature on the Cisco AS5350XM, Cisco AS5400XM, and Cisco VGD 1T3 voice gateways, enter the media forking command in dial-peer configuration mode, voice-service voip...
Page 176 Cisco gateway, then all of the re-invite would function as described. If the terminating gateway is not a Cisco gateway, the re-invite may not indicate that it is a modem. In this case, the originating gateway assumes that it is a fax pass-through call.
Page 177 Select the codec g711ulaw keyword to indicate G.711 mu-law (64,000 bps) for T1 • Select the codec g711 ulaw redundancy keywords to use packet redundancy for modem traffic (in • compliance with RFC 2198) Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 178 To disable the signaling customization, use the no form of this command. You can configure the system to deviate from a country's default settings as defined by Cisco. To do this, choose invert-abcd as an optional keyword: cas-custom channel {define | ignore | invert-abcd} The invert-abcd keyword inverts the ABCD bits before TX and after RX.
Page 179 IPCC Dialer into the PVDM2 DSP voice feature card (VFC) and ISR PVDM2 DSP. The fax/modem detection portion uses existing logic in the PVDM2 DSP. This feature is enabled by the following Cisco IOS commands in voice service voip configuration mode: cpa [threshold | timing] •...
Page 180 If no template is used, all fax relay VSAs are sent when gateway accounting is enabled. The proposed VSAs are presented to the AAA server as formatted text strings. Prior to Cisco IOS Release 12.4(24)T, these attributes were available for NextPort DSPs. Beginning with Cisco IOS Release 12.4(24)T, these attributes are added for HPI-based 5510 DSPs.
Page 181: Additional References
Voice Enhancement Features for Cisco IOS Release 12.4(24)T Additional References Additional References The following sections provide references related to the Voice Enhancements for Cisco IOS Release 12.4(24)T features. Related Documents Related Topic Document Title Basic Overview and Configuration Information for Cisco IOS SIP Configuration Guide Session Initiation Protocol.
Page 182: Technical Assistance
Table 1 lists the release history for this feature. Not all commands may be available in your Cisco IOS software release. For release information about a specific command, see the command reference documentation. Use Cisco Feature Navigator to find information about platform support and software image support.
Page 183 CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks;...
Page 184 Voice Enhancement Features for Cisco IOS Release 12.4(24)T Feature Information for Voice Enhancement Features for Cisco IOS Release 12.4(24)T Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 185: Using The Setup Script
Configuration Using the Command-Line Interface,” for step-by-step instructions. The setup script in this chapter is a typical example using a version of Cisco IOS software that may not exactly match your newly loaded software; however, message prompts are similar. Getting Started...
Page 186 It takes a few minutes for the messages to stop. The messages look similar to the following display. The displayed messages depend on the Cisco IOS software release and feature set you selected. The Note screen displays in this section are for reference only and might not exactly reflect the messages on your console.
Page 187 Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Sat 29-Jan-05 02:10 by yiyan Image text-base: 0x60011068, data-base: 0x61F80000 Cisco AS5400XM (BCM) processor (revision 0x21) with 393215K/131072K bytes of memory. Processor board ID JAB082904P4 SB-1 CPU at 750MHz, Implementation 1025, Rev 0.3, 256KB L2 Cache...
Page 188 Controller CT3 0,1...etc in software corresponds to Port 0,1...etc on the back of the access server. PRI configuration can be configured to controllers all at once Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 189 [j] r1-modified [k] r1-turkey [l] sas-ground-start [m] sas-loop-start Note Signaling type R1-ITU is not supported on the Cisco AS5400 platform. Enter the tone signaling type. Step 19 The following tone signaling types are available: dtmf | mf Enter the tone signal type [dtmf]: Step 20 Enter yes to configure digital number identification service (DNIS).
Page 190 Power up the gateway. The power switch is on the rear panel, at the upper right corner near the power cord, as shown in Figure Messages begin to appear in your terminal emulation program window. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 191 It takes a few minutes for the messages to stop. The messages look similar to the following display. The displayed messages depend on the Cisco IOS software release and feature set you selected. The Note screen displays in this section are for reference only and might not exactly reflect the messages on your console.
Page 192 Getting Started Cisco AS5400XM (BCM) processor (revision 0x21) with 393215K/131072K bytes of memory. Processor board ID JAB082904P4 SB-1 CPU at 750MHz, Implementation 1025, Rev 0.3, 256KB L2 Cache Last reset from IOS reload Manufacture Cookie Info: EEPROM Version 0x4, Board ID 0x4BD, Board Hardware Version 1.11, Item Number 800-6572289-01,...
Page 193 Configuring controller parameters: Press Enter for every slot, port, and channel. Step 13 Configuring controller T1 1/0: Configuring PRI on this controller. Configuring controller T1 1/1: Configuring PRI on this controller. Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 194 AS54-DFC-108NP universal port cards, take the following steps. Power up the gateway. The power switch is on the rear panel, at the upper right corner near the power Step 1 cord, as shown in Figure Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 195 It will take a few minutes for the messages to stop. The messages look similar to the following display. The displayed messages depend on the Cisco IOS software release and feature set you selected. The Note screen displays in this section are for reference only and probably will not exactly reflect the messages on your console.
Page 196 Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Sat 29-Jan-05 02:10 by yiyan Image text-base: 0x60011068, data-base: 0x61F80000 Cisco AS5400XM (BCM) processor (revision 0x21) with 393215K/131072K bytes of memory. Processor board ID JAB082904P4 SB-1 CPU at 750MHz, Implementation 1025, Rev 0.3, 256KB L2 Cache...
Page 197 Enter the number of controllers you will be using for the PRI configuration, or press Enter to configure Step 12 all controllers. Enter # of controllers, you will be using for PRI configuration [16]: Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 198 “Save the Configuration File.” Step 18 Save the Configuration File To save the configuration file, follow these steps: Enter 0, 1, or 2 when the following prompt is displayed: Step 1 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 199 AS5400# setup Modify the existing configuration or configure additional features with the CLI as described in the • Dial Solutions Configuration Guide, the Dial Solutions Command Reference Guide, the Cisco IOS software configuration guide, and command reference publications. See the “Obtaining Documentation”...
Page 200 CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks;...
Page 201: Entering The Rom Monitor Program
The information in this chapter applies to the Cisco AS5350XM and Cisco AS5400XM universal gateways. This chapter describes the Cisco AS5350XM and Cisco AS5400XM ROM monitor, the first software to run when the gateway is powered-up or reset. The ROM monitor can help you isolate or rule out hardware problems encountered when installing your gateway.
Page 202: Rom Monitor Command Conventions
PROM in hex list the device table list files in file system disassemble instruction stream frame print out a selected stack frame Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 203 -x, load image but do not execute, and -v, verbose. The form of the boot command follows: The Cisco AS5350XM and Cisco AS5400XM universal gateways support the following three boot commands at the ROM monitor level: boot [-xv] [devid] [imagename] b—load/run the first XM image on flash.
Page 204 The configuration register resides in NVRAM. The configuration register is identical in operation to other Cisco gateways. Enter the confreg command for the menu-driven system, or enter the new value of the register in hexadecimal.
Page 205 [fe | ge]—The Cisco AS5350XM and AS5400XM universal gateway Ethernet ports are • Gigabit Ethernet ports (labeled GE0 and GE1 on the chassis). The Cisco IOS firmware and software is designed so that configurations for Fast Ethernet will work on the Cisco AS5350XM and AS5400XM universal gateways without requiring any modification by the user.
Page 206 (NVRAM). For example: rommon 9 > meminfo Main memory size:128 MB. Packet memory size:64 MB Available main memory starts at 0xa000e000, size 0x7ff2000 Packet memory starts at 0xa8000000 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 207 System Return Info: count: 19, reason: user break pc:0x60043754, error address: 0x0 Stack Trace: FP: 0x80007e78, PC: 0x60043754 FP: 0x80007ed8, PC: 0x6001540c FP: 0x80007ef8, PC: 0x600087f0 FP: 0x80007f18, PC: 0x80008734 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 208 CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks;...
Page 209: Comprehensive Configuration Examples
This chapter includes sample outputs of the show config command after you have completed the procedures in Chapter 2, “Verifying Basic Setup,” and have configured various advanced features. The following examples are useful references for you only if you are experienced with the Cisco IOS software: CT3 CAS/ISDN with RADIUS, page 1 •...
Page 210 6 controller t1 7 controller t1 8 controller t1 9 controller t1 10 controller t1 11 controller t1 12 controller t1 13 controller t1 14 controller t1 15 controller Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 211 1-24 controller T1 1/0:10 framing esf pri-group timeslots 1-24 controller T1 1/0:11 framing esf pri-group timeslots 1-24 controller T1 1/0:12 framing esf pri-group timeslots 1-24 controller T1 1/0:13 framing esf Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 212 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 1/0:25 framing esf ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 1/0:26 framing esf ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 213 Serial1/0:2:23 ip address 10.1.1.2 255.255.255.0 no ip directed-broadcast encapsulation ppp ip mroute-cache logging event link-status no keepalive dialer idle-timeout 72000 either Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 214 Serial1/0:6:23 ip address 10.1.5.2 255.255.255.0 no ip directed-broadcast encapsulation ppp ip mroute-cache logging event link-status no keepalive dialer idle-timeout 72000 either dialer-group 1 isdn switch-type primary-5ess isdn incoming-voice data Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 215 72000 either dialer-group 1 isdn switch-type primary-5ess isdn incoming-voice data no fair-queue no cdp enable ppp authentication chap Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 216 72000 either dialer-group 1 isdn switch-type primary-5ess isdn incoming-voice modem fair-queue 64 256 0 no cdp enable ppp authentication chap interface Serial1/0:15:23 ip address 10.1.14.2 255.255.255.0 no ip directed-broadcast encapsulation ppp Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 217 172.16.0.0 255.0.0.0 172.22.36.1 ip route 172.16.0.0 255.0.0.0 172.22.36.1 ip route 192.168.173.0 255.255.255.0 172.22.36.1 ip route 192.168.243.0 255.255.255.0 172.22.36.1 no ip http server logging facility local5 logging 192.168.1.137 dialer-list 1 protocol ip permit Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 218 Building configuration ... Current configuration: version 12.1 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption service internal hostname CT3-Mixed-UUT no boot startup-test logging buffered 32000 debugging Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 219 21 controller t1 22 controller t1 23 controller t1 24 controller t1 25 controller t1 26 controller t1 27 controller t1 28 controller controller T1 1/0:1 framing esf pri-group timeslots 1-24 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 220 1-24 controller T1 1/0:15 framing esf pri-group timeslots 1-24 controller T1 1/0:16 framing esf pri-group timeslots 1-24 controller T1 1/0:17 framing esf ds0-group 0 timeslots 1-24 type e&m-fgb Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 221 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 1/0:28 framing esf ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 interface GigabitEthernet0/0 description VLAN 6 ip address 192.168.6.100 255.255.255.0 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 222 Serial1/0:3:23 ip address 10.1.2.2 255.255.255.0 no ip directed-broadcast encapsulation ppp ip mroute-cache logging event link-status no keepalive dialer idle-timeout 72000 either dialer-group 1 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 223 10.1.6.2 255.255.255.0 no ip directed-broadcast encapsulation ppp ip mroute-cache logging event link-status no keepalive dialer idle-timeout 72000 either dialer-group 1 isdn switch-type primary-5ess isdn incoming-voice data no fair-queue no cdp enable Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 224 72000 either dialer-group 1 isdn switch-type primary-5ess isdn incoming-voice modem no fair-queue no cdp enable ppp authentication chap interface Serial1/0:12:23 ip address 10.1.11.2 255.255.255.0 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 225 64 256 0 no cdp enable ppp authentication chap interface Serial1/0:16:23 ip address 10.1.15.2 255.255.255.0 no ip directed-broadcast encapsulation ppp ip mroute-cache logging event link-status Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 226 RO snmp-server contact Test123456 snmp-server chassis-id 'router for AS5400 ct3' line con 0 exec-timeout 0 0 logging synchronous transport input none line aux 0 exec-timeout 0 0 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 227 6/0 6/107 resource-pool profile customer 4700 limit base-size 110 limit overflow-size 18 resource 4700 speech dnis group default resource-pool profile customer 5300 limit base-size 538 limit overflow-size 18 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 228 25 controller t1 26 controller t1 27 controller t1 28 controller controller T1 7/0:1 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:2 framing esf Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 229 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:14 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:15 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 230 T1 7/0:26 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:27 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 231 172.16.14.0 255.255.255.0 192.168.21.10 ip route 172.17.14.0 255.255.255.0 192.168.21.10 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 232 30 aaa accounting network default start-stop group aaa.router enable password password Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 233 1 controller t1 2 controller t1 3 controller t1 4 controller t1 5 controller t1 6 controller t1 7 controller t1 8 controller t1 9 controller t1 10 controller Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 234 T1 7/0:8 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:9 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 235 T1 7/0:21 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:22 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 236 Serial0/0 no ip address no ip directed-broadcast clockrate 2000000 interface Serial0/1 no ip address no ip directed-broadcast shutdown clockrate 2000000 interface Group-Async0 no ip address no ip directed-broadcast no group-range Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 237 0 0 logging synchronous transport input none line aux 0 exec-timeout 0 0 logging synchronous transport input all line vty 0 4 password password no logging synchronous line 1/00 6/107 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 238 0 cns event-service server mta receive maximum-recipients 0 controller T1 2/0 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-24 controller T1 2/1 framing esf linecode b8zs Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 239 1-24 controller T1 5/2 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-24 controller T1 5/3 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-24 controller T1 5/4 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 240 64 256 0 clockrate 2000000 interface Serial0/1 no ip address no ip directed-broadcast no ip route-cache no ip mroute-cache shutdown clockrate 2000000 interface Serial2/0:23 no ip address Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 241 64 256 0 no cdp enable interface Serial2/7:23 no ip address no ip directed-broadcast isdn switch-type primary-5ess isdn incoming-voice modem fair-queue 64 256 0 no cdp enable interface Serial5/0:23 no ip address Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 242 Serial5/7:23 no ip address no ip directed-broadcast isdn switch-type primary-5ess isdn incoming-voice modem fair-queue 64 256 0 no cdp enable interface Async1/00 ip address 172.16.97.1 255.255.255.0 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 243 172.16.100.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache dialer in-band dialer idle-timeout 2000000 dialer string 7150100003 dialer-group 1 async default routing async mode interactive Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 244 Async1/07 ip address 172.16.104.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache dialer in-band dialer idle-timeout AS5400 dialer string 7150100007 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 245 Async1/12 ip address 172.16.109.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 246 Async1/16 ip address 172.16.113.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache dialer in-band dialer idle-timeout AS5400 dialer string 7150100016 dialer-group 1 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 247 AS5400 dialer string 7150100020 dialer-group 1 async mode interactive no peer default ip address ppp authentication chap interface Group-Async0 ip unnumbered GigabitEthernet0/0 no ip directed-broadcast Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 248 0 logging synchronous line vty 0 4 password 7 1042081B no logging synchronous login line 1/00 1/107 autoselect ppp script dialer dial logging synchronous modem InOut transport input all Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 249 192.168.10.1 ip subnet-zero no ip domain-lookup ip host jurai 172.23.254.253 isdn switch-type primary-net5 isdn voice-call-failure 0 cns event-service server mta receive maximum-recipients 0 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 250 E1 7/7 pri-group timeslots 1-31 interface GigabitEthernet0/0 ip address 192.168.10.103 255.255.255.0 no ip directed-broadcast no ip route-cache no ip mroute-cache interface GigabitEthernet0/1 no ip address no ip directed-broadcast no ip route-cache Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 251 64 256 0 no cdp enable interface Serial6/5:15 no ip address no ip directed-broadcast isdn switch-type primary-net5 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 252 64 256 0 no cdp enable interface Serial7/5:15 no ip address no ip directed-broadcast isdn switch-type primary-net5 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 253 Async5/107 ip unnumbered GigabitEthernet0/0 no ip directed-broadcast encapsulation ppp async mode interactive ppp authentication chap interface Group-Async0 no ip address Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 254 0 chat-script dial ABORT ERROR ABORT BUSY ABORT "NO CARRIER" TIMEOUT 120 "" at OK "\datd,,\T" CONNECT cns event-service server mta receive maximum-recipients 0 controller T1 2/0 framing esf Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 255 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 3/0 framing esf linecode b8zs cablelength short 133 ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 3/1 framing esf linecode b8zs Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 256 192.168.10.100 255.255.255.0 no ip directed-broadcast duplex auto speed auto interface GigabitEthernet0/1 no ip address no ip directed-broadcast no ip route-cache no ip mroute-cache shutdown duplex auto speed auto interface Serial0/0 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 257 172.21.1.0 255.255.255.0 192.168.21.10 ip route 172.22.1.0 255.255.255.0 192.168.21.10 no ip http server dialer-list 1 protocol ip permit line con 0 exec-timeout 0 0 logging synchronous transport input none Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 258 1/0 1/107 resource-pool group resource group2 range port 4/0 4/107 range port 5/0 5/107 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 259 0 controller T1 2/1 framing esf linecode b8zs cablelength short 133 ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 2/2 framing esf linecode b8zs cablelength short 133 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 260 133 ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 3/3 framing esf linecode b8zs cablelength short 133 ds0-group 0 timeslots 1-24 type e&m-fgb Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 261 2000000 interface Serial0/1 no ip address no ip directed-broadcast no ip route-cache no ip mroute-cache shutdown clockrate 2000000 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 262 0 exec-timeout 0 0 logging synchronous transport input none line aux 0 logging synchronous line vty 0 4 password 7 13091610 no logging synchronous login line 1/00 1/107 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 263 1/0 1/107 resource-pool group resource group2 range port 4/0 4/107 range port 5/0 5/107 resource-pool group resource group3 range port 6/0 6/107 range port 7/0 7/107 resource-pool profile customer bell_atlantic Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 264 1-24 controller T1 2/2 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-24 controller T1 2/3 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-24 controller T1 2/4 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 265 133 pri-group timeslots 1-24 controller T1 5/5 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-24 controller T1 5/6 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-24 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 266 64 256 0 no cdp enable interface Serial2/2:23 no ip address no ip directed-broadcast isdn switch-type primary-5ess isdn incoming-voice modem Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 267 64 256 0 no cdp enable interface Serial5/2:23 no ip address no ip directed-broadcast isdn switch-type primary-5ess isdn incoming-voice modem Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 268 1000 in hold-queue 1000 out interface Async1/01 ip address 172.16.98.1 255.255.255.0 no ip directed-broadcast Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 269 2000000 dialer string 7150100004 dialer-group 1 async default routing async mode interactive no peer default ip address Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 270 AS5400 dialer string 7150100008 dialer-group 1 async mode interactive ppp authentication chap interface Async1/09 ip address 172.16.106.1 255.255.255.0 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 271 Async1/13 ip address 172.16.110.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache dialer in-band dialer idle-timeout AS5400 dialer string 7150100013 dialer-group 1 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 272 AS5400 dialer string 7150100017 dialer-group 1 async mode interactive no peer default ip address ppp authentication chap Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 273 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 274 InOut transport input all line 3/00 4/107 autoselect ppp script dialer dial logging synchronous modem InOut transport input all line 6/00 7/107 autoselect ppp Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 275 3/0 3/107 resource-pool profile customer bell_atlantic limit base-size all limit overflow-size 0 resource group2 speech dnis group group2 resource-pool profile customer us_west limit base-size 60 limit overflow-size 100 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 276 E1 6/6 pri-group timeslots 1-31 controller E1 6/7 pri-group timeslots 1-31 controller E1 7/0 pri-group timeslots 1-31 controller E1 7/1 pri-group timeslots 1-31 controller E1 7/2 pri-group timeslots 1-31 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 277 64 256 0 no cdp enable interface Async1/00 ip unnumbered GigabitEthernet0/0 no ip directed-broadcast encapsulation ppp async mode interactive ppp authentication chap Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 278 1 protocol ip permit line con 0 exec-timeout 0 0 transport input none speed 9600 line aux 0 line vty 0 4 login CT3 with Resource Pooling, AAA, and Modem AS5400# show config Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 279 18 resource 4700 speech resource-pool profile customer 5300 limit base-size 538 limit overflow-size 18 resource 5300 speech dnis group elnino resource-pool profile service gold modem min-speed 33200 max-speed 56000 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 280 1 controller T1 7/0:7 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:8 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 281 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:20 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:21 framing esf Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 282 4000 out interface GigabitEthernet0/1 ip address 172.22.35.71 255.255.0.0 shutdown duplex auto speed auto interface Serial0/0 no ip address shutdown clockrate 2000000 interface Serial0/1 no ip address hutdown Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 283 192.168.1.137 auth-port 1645 acct-port 1646 radius-server host 192.168.1.138 auth-port 1645 acct-port 1646 radius-server retransmit 2 radius-server timeout 9 radius-server deadtime 30 radius-server key lab line con 0 exec-timeout 0 0 logging synchronous Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide...
Page 284 CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks;...

This manual is also suitable for:

As5400xm

Cisco AS5350XM Configuration Manual

Quick Links

Related Manuals for Cisco AS5350XM

Summary of Contents for Cisco AS5350XM

This manual is also suitable for:

Table of Contents