1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Projection Screen
  5. Room Panorama
  6. Installation manual

Cisco Room Panorama Installation Manual

85-inch main screens
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Cisco Room Panorama
85-INCH MAIN SCREENS
Installation guide

Advertisement

Table of Contents
loading

Related Manuals for Cisco Room Panorama

Summary of Contents for Cisco Room Panorama

  • Page 1 Cisco Room Panorama 85-INCH MAIN SCREENS Installation guide...
  • Page 3 In addition, integrated microphones are part of the state of the art speaker tracking solution. The cosmetic wall panels shown here are available The Cisco Room Panorama system is designed to make your video as an option. conferencing room more versatile and flexible also for local meetings.

  • Page 4: Table Of Contents

    Table of contents Before you start the installation................3 Installing Room Panorama with a custom wall ..........95 Packaging ......................4 Extra requirements and preparations when building a custom wall ....96 Screws and tools ....................5 A1. Mount the rails and risers ...............100 A2. Build the custom wall structure ............100 Installing Room Panorama with cosmetic wall panels ........6...

  • Page 5: Before You Start The Installation

    Room Panorama. A new main screen model for Room Panorama was introduced in 2023. The new model is 85 inches; the original model was 82 inches. Room Panorama has the same functionality regardless of main screen model. However, since there are a few installation and cabling differences between them, there are two sets of installation instructions and wiring diagrams online.

  • Page 6: Packaging

    Packaging Risk of personal injury You have received four or five pallets with parts Boxes and labels There is a potential hazard risk tied and components, depending on whether you have to the gas springs in the screen There are several boxes with parts on each pallet. ordered the optional cosmetic wall.

  • Page 7: Screws And Tools

    Screws and tools Required tools and equipment Screws and spacers • Two stepladders The following kit of screws and spacers are shipped with the product. The kit is • Drill in box A1. • Torx 20, Torx 25, Torx 30, and Torx 40 bits •...

  • Page 8: Installing Room Panorama With Cosmetic Wall Panels

    Part 1 Installing Room Panorama with cosmetic wall panels This part of the guide explains how to install the Room Panorama with the optional cosmetic wall panels offered by us. As an alternative to these cosmetic wall panels, you can integrate the Room Panorama system fully in the room by making your own custom wall integration.

  • Page 9: Fasten The Horizontal Rails

    1. Fasten the horizontal rails The Room Panorama system is mounted on three left part center part right part rails - top, middle, and bottom. The rails are fastened to the wall. Top rail The rails must be level, and accurately centered about the system’s vertical center line.
  • Page 10 ×n left and right parts joining bracket (FH M4x10, Torx 20) You also need the number and type of screws that are required for fastening the rails safely to the wall (not provided by Cisco).
  • Page 11 3. Fasten a joining bracket on each side of the 4. Fasten the left and right part of the rail to center rail the center part. (FH M4x10, Torx 20) ×2 Depending on the type of wall, you may need to remove the part temporarily after marking the mounting points on the wall.
  • Page 12 1.2. Fasten the middle rail 1.3. Fasten the bottom rail Use the same procedure as for the upper rail, but Use the same procedure as for the upper rail, but measure the distance from the upper rail and not measure the distance from the middle rail and not from the floor.

  • Page 13: Mount The Vertical Risers

    2. Mount the vertical risers 2.1. Assemble the risers Enter the upper part into the lower part, and fasten with two screws . Repeat for all the risers. (M6x12, Torx 30) The system has seven vertical risers, which are attached to the rails. The center riser differs from the others;...
  • Page 14 2.2. Fasten the risers to the rails The risers are fastened to the rails with screws , one in each rail. (M6x12, Torx 30) Repeat the same procedure to fasten the seven risers. 1. Enter a screw into the top rail, 2.
  • Page 15 5. Temporarily adjust the foot on the riser, so that the riser rests on the floor. Do not tighten the upper nut to lock its position now. 6. Repeat steps 1-5 for all risers. 8. Tighten the screws that fasten the risers to the rails.

  • Page 16: Place The Subwoofers

    3. Place the subwoofers 3.1. Place the subwoofer stands ×4 The system has four subwoofers. They are placed Place the stands as far to the in stands on the floor. Repeat the same procedure front as possible. for all stands and subwoofers. Check that the metal does not touch the risers.
  • Page 17 3.2. Place the subwoofers in the stands ×4 Note that - counting from the left: • Subwoofer number 1 and 3: Black finish facing the room • Subwoofer number 2 and 4: Silver finish facing the room Push the subwoofer all the way down into the stand. Check that the foam doesn't curl when pushing it down.

  • Page 18: Mount The Cavities

    4. Mount the cavities 4.1. Insert the rack cavity Hang the cavity between the two risers as shown in the illustration. Check that the hooks fully enter all slots on both sides (see details on the next The system has six cavities, which are designed page).
  • Page 19 4.2. Insert the cooling cavity There are hooks along both sides of the cavities. Hang the cavity between the risers as shown. The top of the cavity aligns with Hook all of them into the corresponding slots on the rack cavity. the risers.
  • Page 20 4.3. Insert the power cavities 4.4. Insert the display cavities Hang the two power cavities between the risers as shown. They are identical. Hang the two display cavities between the risers as shown. They are identical. The top of the cavities aligns with the rack cavity. The top of the cavities aligns with the rack cavity.
  • Page 21 4.5. Fasten the six cavities with screws Fasten each cavity with two screws on each side , as shown for (M6x12, Torx 30) the rack cavity in this illustration.

  • Page 22: Fasten The Mounting Plates For The Speakers

    5. Fasten the mounting plates for the speakers There are mounting plates for the speakers above the cavities. The left and right plates are not identical; they are marked with L and R, respectively. Take care to put them in the correct position. Repeat the same procedure for both plates.
  • Page 23 1. Hang the mounting plate on the risers. Check 2. Secure the mounting plate with one screw at that the hooks enter all slots on both sides. center. Take care to mount the plate on the correct side. The widest flap is toward center. This is the left side plate (also marked with an L).

  • Page 24: Mount The Psu Bracket

    6. Mount the PSU bracket Fasten the PSU bracket on the right side of the left power cavity with three screws. 1. Place the PSU bracket on the right side of the 2. Add two more screws, and fasten them all. left power cavity.

  • Page 25: Mount The Codec And Amplifier

    7. Mount the codec and amplifier 7.1. Mount the codec The codec and amplifier are placed in the rack cavity. The connector panels are facing 2. Remove the rubber feet from the codec. 1. Remove the eight pre-mounted screws upward. 3.
  • Page 26 7.2. Mount the amplifier Slide the amplifier into its slot. Fasten it with four screws (M5x10, Torx 25) ×2...

  • Page 27: Attach The Rating Label

    Complies with XXXXXXXXXX IMDA standards DB101992 www.bis.gov.in Includes Cisco Codec Model TTC6-13, IFETEL certificate RCPCXXXXX-XXXX-XX Incluye Códec (Sistema de videoconferencia) Cisco modelo TTC6-13, certificado del IFETEL RCPCXXXXX-XXXX-XX C6-13 with CNC ID: C-22508 Includes Cisco Codec TTC6-13 with CNC ID: C-XXXXX...

  • Page 28: Mount The Ethernet Switch

    9. Mount the Ethernet switch The system has two Ethernet switches; the first 1. Fasten the rack ears to the switch. One screw 2. Slide the switch into its slot, and fasten it with one is placed in the cooling cavity. for each rack ear four screws (PAN10-32x0.312, PH2)

  • Page 29: Mount The Antennas

    10. Mount the antennas Skip this step if you have a non-radio product. Non-radio products, which have the letters 'NR' in their product identifier (PID), are delivered without antennas. 1. Fasten the antenna support below the left 2. Thread the two antennas up through the small 3.

  • Page 30: Mount The Fan Module

    11. Mount the fan module 1. Hold the fan module with the cables upward. 2. Fasten the fan kit with two screws 3. Connect the fan cables to the amplifier. Thread the cables through the small holes in (M6x12, Torx 30) Which fan is connected to which input does the cooling cavity, and insert the fan module in not matter.

  • Page 31: Connect Cables

    Presentation sources Touch panels (user interface) Microphones 78-101909-01C0 (CS-T10-TS+) (CS-MIC-ARRAY-T) © 2023 Cisco Systems, Inc. All rights reserved. You find velcro straps in box The wiring diagram is also available online, at https://www.cisco.com/go/panorama-installation Do not connect to power! Cable marking Do not connect any power cords to the socket outlets at this point in the installation.
  • Page 32 12.1. Loudspeaker cables 12.2. Power cable for the Ethernet switch in the system 1. Connect cable bundles (left) and (right) to the amplifier as shown in 1. Connect the power cable (X4) to the Ethernet switch in the system. the diagram. The power socket is facing downward, so you must connect it from below.
  • Page 33 12.3. PSUs for the amplifier 12.4. One Connect cables The One Connect cables, which connect the main screens to their One 1. Place the two PSUs in the bracket in the left power cavity. Connect boxes, will be connected later: •...
  • Page 34 12.7. Other cables Connect all the other cables as shown in the wiring diagram, and note the following. Cables for the camera: Cable for the Ethernet switch in the system: • The camera will be installed later. • Connect the Ethernet switch in the system to the codec (X3). •...

  • Page 35: Organize The Cables Neatly

    13. Organize the cables neatly The system has many cables! To avoid rattling noise and to have a nice looking system we recommend you to fasten the cables to the steel structure with velcro straps. The main cable routes are: •...

  • Page 36: Mount Brackets For The Cosmetic Panels

    14. Mount brackets for the cosmetic panels Brackets Corner bracket, left and right Riser bracket Front profile (3203 #3) Corner bracket (M6x12, Torx 30) (M4x12, Torx 20) Riser brackets (5x) (Washer, 0.9 mm) Corner bracket...
  • Page 37 14.1. Corner brackets 14.2. Riser brackets The system has a corner bracket on each side. The system has a small bracket on five of the Repeat the procedure for both corners. risers (all except the outer risers). Repeat the procedure for the five risers. 1.
  • Page 38 14.3. Level the brackets We recommend that you use the laser level to check that the holes in the corner and riser brackets are level. If not, adjust the feet on the risers and corner brackets until level. Remember to pull the subwoofers forward again when done.
  • Page 39 14.4. Profiles for the upper panels There is a profile in front of each speaker mounting plate. Fasten the profile to the (3203 #3) mounting plate with three screws (M4x12, Torx 20) Repeat the procedure for both profiles. ×3 Add two washers to each screw, between the profile and the mounting plate.

  • Page 40: Mount The Flex Tubes For Cables

    15. Mount the flex tubes for cables Two flex tubes run from the rack cavity toward the 1. Add an adapter to both tubes and tighten. 2. Unscrew and remove the nut from the floor. You need them to route the cables between adapters.
  • Page 41 3. Insert the tubes into the holes in the rack 4. Guide the two tubes down on each side of 5. Fasten the tubes to the riser and bracket with cavity from below. Attach them by putting the center riser. Cut them at the appropriate cable ties, in order to prevent the tubes from back and tightening the nuts.

  • Page 42: Mount The Bottom Trim

    16. Mount the bottom trim The bottom trim stands on the floor and is fastened to the corner and riser brackets. The trim is fastened through the front and side profiles as shown in the close-up illustrations. Bottom trim and brackets Bottom trim, left and right Center trim Front profile...
  • Page 43 1. Fasten the trim, through a front profile 2. Fasten the center trim, through a front profile 3. Fasten the trim, through a side profile (3203 #5) (3203 #1) with five screws , with six screws with two screws. (M4x12, Torx 20) (3203 #5) (M4x12, Torx 20) Repeat the procedure for both the left and...

  • Page 44: Mount The Upper Trim

    17. Mount the upper trim 17.1. Fasten the upper trim support The top trim and its support are fastened to 1. Enter three screws into the rail 2. Hang the trim support onto the screws. You (M6x12, Torx 30) the risers and rails as shown in the close-up and risers as shown, without tightening.
  • Page 45 17.2. Fasten the upper trim 1. Enter three screws into the trim 2. Hang the trim onto the screws. (M4x12, Torx 20) support as shown, without tightening. 3. Tighten the three screws, and add two more - one of them with a spacer and (M4x12, Torx 20) two washers.

  • Page 46: Mount The Content Cavity And Screen Mount Brackets

    18. Mount the content cavity and screen mount brackets 18.2. Mount the cavity Hang the cavity on the risers and fasten with four screws (M6x12, Torx 30) The content cavity, with the mounting brackets for 18.1. Find the cables the content screen, is above the cooling and rack cavities.
  • Page 47 18.3. Place the screen cables 18.4. Mount the upper screen bracket 18.5. Mount the lower screen bracket Thread the cables for the content screen up 1. Enter one screw into the cavity 1. Enter two screws into the cavity (M6x12, Torx 30) (M6x12, Torx 30) through the holes in the content cavity: as shown, without tightening.

  • Page 48: Mount The Cosmetic Panels

    19. Mount the cosmetic panels Before you start mounting the panels, take The subwoofers and the rear side of the Ethernet an extra look to assure that these cables are switch are not easily accessible once the panels connected: have been mounted. •...
  • Page 49 19.1. Mount the lower corner panels Repeat the procedure on both sides. 1. Add a small bracket to the middle rail, and 2. Place the corner panel onto the profiles. fasten with a screw ( M6x12 Make sure to fit the groove of the panel fully onto both profiles, and Do not tighten the screw now.
  • Page 50 19.2. Mount a joining module on top of the lower corner panel Repeat the procedure on both sides. 1. Fasten the vertical profile ( ) with two 2. Add two screws with spacers 3. Fasten the two horizontal profiles ( ) with 3203 #1 (M4x12, Torx 20;...
  • Page 51 4. Place the joining module onto the corner 5. Fasten the module with one screw panel. (M6x12, Torx 30) Do not tighten Make sure to fit the module fully into the this screw now. groove of the panel on all sides. Check that the screws with spacers enter the corresponding slots at the rear side of the panel.
  • Page 52 19.3. Attach a side trim to the lower corner panel 19.4. Insert a profile in the corner panel Attach a side trim to the corner panel. The left and Insert a profile into the groove of the (3201 #2) right trims are not identical. Take care to put them panel, below the side trim.
  • Page 53 19.5. Insert the lower front panels Slide the lower front panel onto the profiles, both at the bottom and at the outer side. Make sure to fit the groove of the panel fully onto both profiles. Repeat the procedure on both sides. There is no profile between the two lower front panels.
  • Page 54 19.6. Attach the wall top trims The left and right trims are different; check that you mount them the correct way. Fit the trim fully into the groove of the front panel, before you fasten them. Repeat the procedure on both sides. Three screws from the front.
  • Page 55 19.7. Straighten the lower corner panels and tighten screws Before tightening the screws, make sure the lower corner panel is straight and plumb. Repeat the procedure on both sides. 1. Make sure the corner panel is straight and 2. Tighten the screws that you entered without 3.
  • Page 56 19.8. Mount the upper corner panels Repeat the procedure on both sides. 1. Add a screw with spacer to the upper panel 2. Place the panel lock onto the upper corner 3. Place the upper corner panel on top of the lock panel.
  • Page 57 5. Make the split line between the upper and lower corner panels as tight and even as possible. When done, fasten the bracket to the top trim with one screw (M4x12, Torx 20) Straight and plumb...
  • Page 58 19.9. Mount a profile to the corner panel 19.10. Mount the upper front panels Repeat the procedure on both sides. Repeat the procedure on both sides. 1. Insert a profile into the groove of the panel. Slide the upper front panel onto the profiles, both at the bottom and at the outer (3201 #3) side.
  • Page 59 19.11. Align the upper panels There are two adjustment screws and one support screw below each upper front panel. These screws are for aligning the upper panels and make the split lines between panels as tight and even as possible. Support screws Adjustment screws (one on each profile)
  • Page 60 19.12. Attach a side trim to the upper front panel Attach a side trim to the upper front panel. The left and right trims are not identical. Take care to mount them on the correct side. 2. Pivot the trim. Make sure it fits fully into the 3.
  • Page 61 19.13. Adjust spacers for the screens The system has six adjustable spacers, which prevents the screens from leaning on the cosmetic panels. Content screen ×2 Adjustable spacers, content screen 7 mm (0.3 in.) Adjust the spacers so that they are 7 mm (0.3 in.) deeper than the cosmetic panels.

  • Page 62: Mount The Camera

    20. Mount the camera 20.1. Mount the camera bracket 20.2. Set the camera tilt angle to 10° The camera bracket is fastened to the content There are two sliders for adjusting the camera tilt cavity with two screws angle at the bottom of the camera. (M6x12, Torx 30) The camera is mounted on a bracket that is fastened to the content cavity.
  • Page 63 20.3. Snap the camera onto the bracket 20.4. Connect the camera cables Click the camera onto the bracket. You should hear a click sound from both 1. Connect the cables to the camera according to the wiring diagram: entry points. •...

  • Page 64: Mount The Fan Duct

    21. Mount the fan duct The fan duct is placed in front of the fans, just below the camera. It's fastened with three screws. Fan duct Push the duct gently upward toward the camera when tightening the screws (M6x12, Torx 30) Fan duct You want the duct as close to the camera as possible, but don't push so hard that the camera...

  • Page 65: Mount The Loudspeakers

    22. Mount the loudspeakers 22.1. Mount the loudspeaker mounting structure Repeat this procedure for both sides. There are six loudspeakers on each side. They are 2. Hang the mounting structure onto the screw. 1. Enter a screw into the mounting (M6x12, Torx 30) inserted in a mounting structure that is fastened to plate as shown, without tightening.
  • Page 66 22.2. Mount the screen support profile The screen support profile goes between the two loudspeaker mounting structures; below the camera. ×2 Fasten the profile with four screws (M6x12, Torx 30) two on each side.
  • Page 67 22.3. Insert the loudspeakers The system has twelve loudspeakers; six on each side of the camera. The speakers are identical. We recommend you to start from the center when mounting loudspeakers. Repeat this procedure for all the speakers. 1. Connect the correct cable to 2.

  • Page 68: Mount The Content Screen

    23. Mount the content screen 23.1. Mount rails on the content screen In addition to the screws, you need a set of spacers when mounting the screen rails. You find the spacers in the accessories bag that is in the screen package.
  • Page 69 23.2. Hang the content screen onto the top bracket 23.3. Adjust the screen height Use the two thumb screws at the top to adjust the screen height. The gap between the screen and the loudspeaker mounting structure should be 7 mm (0.28 in.). 7 mm (0.28 in.) Lift screen onto bracket...
  • Page 70 23.4. Tilt the screen and secure it to the lower bracket 23.5. Connect the cables You can use the levers on the screen rails to fix Connect the cables to the content screen the content screen in a tilted position. according to the wiring diagram: •...

  • Page 71: Mount The Right Screen And Deco Grille

    24. Mount the right screen and deco grille The main screens (left and right) will hang on Follow the installation instructions carefully, The deco grille, which is split at center, is attached screen mount modules, which allow you to move installing the right screen first.
  • Page 72 24.1. Unpack one main screen 24.2. Place the One Connect cable in the display cavity The main screens come with a Samsung One The One Connect cable will be used to connect Connect box, a One Connect cable, and other the Samsung One Connect box with the screen.
  • Page 73 24.3. Mount straightening bars on the screen Fasten the long straightening bar to the screen with four screws , and the short (M8x8, Torx 40) straightening bar with two screws (M8x8, Torx 40)
  • Page 74 24.4. Mount rails on the screen Fasten each rail with two screws (M8x8, Torx 40) ×2 Use the holes marked with an "R" for the right screen. You will use the holes marked with an "L" when mounting the left screen in step 25. Use the lower holes in each set.
  • Page 75 24.5. Loosen the rail thumb screws Partially unscrew the thumb screws as shown in the close-ups. It's important that they don't interfere with placing the screen onto the screen mount module in the next step.
  • Page 76 24.6. Hang the screen onto the screen mount module in the display cavity Risk of personal injury There is a potential hazard risk tied to the gas springs in the screen mount modules when installing or dismantling the system. There is no risk involved when following the Install Guide step by step, but if caution is not taken regarding the...
  • Page 77 24.7. Move the screen mount safety brackets to Operational Mode position Each screen mount module has four safety brackets, which are all in Safe Mode position when ×2 shipped. To avoid the risk of personal injury: • Never move the screen mount safety brackets out of the Safe Mode position (transport position) when the screen is NOT hanging on the screen mount...
  • Page 78 24.8. Mount the Samsung One Connect box Each main screen has an associated One Connect box. The One Connect box is in the main screen package. Hang the One Connect box for the right screen on the two pre-mounted screws in the display cavity. The connector panel is facing to the right.
  • Page 79 24.9. Secure the screen Use the levers on the screen rails to fix the screen in a tilted position. Repeat the procedure for both rails. 1. Carefully tilt the screen by lifting out the lower 2. Lift the lever so that the screen stays in a tilted 3.
  • Page 80 24.10. Connect the One Connect cable The One Connect cable is hanging in the display 1. Connect the One Connect cable between the 2. Fasten the cable connector to the screen with cavity; it was winded up and fastened with velcro One Connect box and right screen according the provided cable clip.
  • Page 81 24.11. Connect the other cables to the One Connect box 24.12. Remove the protective film from the screen edges 1. Connect the following cables to the One Connect box according to the The screen comes with a protective film. Leave the film that covers the front wiring diagram.
  • Page 82 24.13. Assemble the deco grille Prepare the deco grille that will be attached below the screen. The left and right grilles are not identical. The curved corner is toward the outside edge. 1. Remove the four screws and spacers from the 2.
  • Page 83 24.14. Mount the deco grille to the screen Repeat this procedure for both brackets. 1. Enter screws in the holes at the 2. Attach the deco grille to the rear of the screen 3. Push the deco grille up and align it to the (M4x8, Torx 20) rear side of the screen, without tightening.
  • Page 84 24.15. Align the deco grille to the screen In order to align the deco grille perfectly to the screen, you may have to adjust the screws from step 24.13. • To align the grille to the front of the screen, loosen the four screws that fasten the grille support to the grille (blue).
  • Page 85 24.16. Lock the screen in vertical position 24.17. Push the screen into normal position 1. Pull the screen slightly outward, so that you can release the levers on both Use the handle and push the screen up to its normal position. sides.

  • Page 86: Mount The Left Screen And Deco Grille

    25. Mount the left screen and deco grille Make sure the right screen is pushed up into normal position before you start installing the left screen. To avoid scratching the screens, we recommend that only one screen is in the lower position at a time.
  • Page 87 Repeat the complete step "24. Mount the right screen and deco grille" on page 69 onward, but this time for the left screen. Note the following when mounting the left screen: • 24.4. Mount rails on the screen 24.17. Push the screen into normal position •...

  • Page 88: Mount The Speaker Grille

    26. Mount the speaker grille 26.1. Mount the speaker grille Place the grille in front of the loudspeakers, and align the two parts nicely. Make the split line Plastic washers on the between the parts as tight as possible. The speaker grille is split at center; each part is inside of the grille fastened by magnets.
  • Page 89 26.2. Insert the deco ring 26.3. Align the main screens to the 26.4. Tilt the content screen back in place speaker grille Place the deco ring around the camera. The ring Pull the content screen slightly outward, so that provides a neat transition between the grill and you can release the levers on both sides.
  • Page 90 26.5. Adjust the height and align the content screen with the speaker grille You may need to adjust the height and depth of Adjust the height of the content screen: Adjust the depth/tilt of the content screen: the content screen to align with the speaker grille. •...

  • Page 91: Mount The Center Part Of The Upper Trim

    27. Mount the center part of the upper trim Add the center part of the upper trim and fasten it with two screws. Upper trim, center ×2 Upper trim, center (M4x12, Torx 20...

  • Page 92: Pull Up And Connect The Cables Between The System And Components On The Table

    28. Pull up and connect the cables between the system and components on the table Note: If you have chosen not to use the flex tubes, you must route the cables (X1, T1...3) from the table to the codec through the hole in the back wall of the rack cavity, connect them as shown in the wiring diagram, and strap them with velcro or cable ties for strain relief.

  • Page 93: Mount The Ethernet Switch In The Table

    This switch is connected to the internal here: the flex tubes and connected to the codec in step Room Panorama network, and cannot be used to Cisco Catalyst 1000 Series 8-Port and 16-Port access the company LAN or Internet. Switch Hardware Installation Guide: Connect the power cable (X2) to the switch, but don't connect it to the socket outlet yet.

  • Page 94: Place Components On The Table

    The presentation cables (T1, T2, T3) were pulled under - or close to - the table, as shown in the in box) and the Cisco Room Panorama Room through the flex tubes and connected to the wiring diagram (T4, T5).

  • Page 95: Finish Up

    70% alcohol. Follow the instructions in the Getting Started Guide to finalize the installation. These steps are mandatory: You can read our general guidelines on how to clean or disinfect Cisco Room 1. Register the system devices here: 2.

  • Page 97: Installing Room Panorama With A Custom Wall

    Part 2 Installing Room Panorama with a custom wall Part 1 of this guide explains how to install the Room Panorama with the optional cosmetic wall panels offered by us. As an alternative to these cosmetic wall panels, you can integrate the Room Panorama system fully in the room by making your own custom wall integration.

  • Page 98: Extra Requirements And Preparations When Building A Custom Wall

    Extra requirements and preparations when building a custom wall Depth of the wall The custom wall must level at the same depth as the cosmetic wall panels provided by us. Otherwise the screen brackets and their hinge mechanism will not work. The hing mechanism is required to allow access to the components behind the screens after the system is fully mounted.
  • Page 99 Subwoofer output and air flow Minimum 20 mm (0.79 in.) Air intake area and subwoofer output Minimum 3.57 m (140.6 in.) Air outlet area The ventilation air intake is close to the floor. It aligns with the four subwoofers, which need an opening toward the room to provide excellent audio quality.
  • Page 100 You may fasten the custom wall to the risers The core mounting structure for the Room Panorama is the horizontal rails and vertical risers as shown in the illustration. This mounting structure must be securely fastened to the wall behind the system.
  • Page 101 The two main options for routing cables between We ship two variants of the subwoofer grille to For the custom wall option you must provide all the Room Panorama system and the components accommodate these cable routing options. It's materials, fasteners, and tools required to make only the center part of the grille that is affected.

  • Page 102: A1. Mount The Rails And Risers

    Preparation Guidelines before you start the installation. They are available online. About the installation procedure The procedure how to install the Room Panorama with a custom wall are referring to the mounting steps in the main part of this installation guide.
  • Page 103 1350 mm (53.15 in.) Minimum 3600 mm (141.73 in.) 1154 mm (45.43 in.) 1154 mm (45.43 in.) 1154 mm (45.43 in.) Minimum 4200 mm (165.4 in.)

  • Page 104: A3. Paint Visible Parts Of The Wooden Structure

    A3. Paint visible parts of the wooden structure Some of the wooden structure is visible when tilting out or pulling down the screens. These areas are colored dark gray in the illustration. We recommend that you paint these parts in a color that blends well with the black metal parts.

  • Page 105: A4. Mount The Antenna Support

    A4. Mount the antenna support Skip this step if you have a non-radio product. Non-radio products, which have the letters 'NR' in their product identifier (PID), are delivered without antennas. Fasten the antenna support between the two risers as shown in the illustration. The antennas themselves face right and inward.

  • Page 106: A5. Mount The Flex Tubes

    A5. Mount the flex tubes Skip this step if you are not going to lead the cables between the video system and the table through the grille and out on the floor. Guide the two tubes down on each side of the center riser.

  • Page 107: A6. Mount The Custom Wallboards

    A6. Mount the custom wallboards Mount the wallboards on the beams. Leave open Fully complete the mounting and finishing of the areas as shown in the illustration. wallboards (e.g. painting) before you continue 50 mm (1.97 in.) with the installation. 30 mm (1.18 in.) Minimum 20 mm (0.79 in.) 1350 mm (53.1 in.)

  • Page 108: A7. Place The Subwoofers And Mount The Rack Cavity

    A7. Place the subwoofers and mount the A8. Complete the flex tube mounting rack cavity Skip this step if you are not routing any cables between the codec and the components on the table across the floor. Follow steps 3-4.1 starting on page 14 in the main part of the installation guide to: •...

  • Page 109: A9. Route The Antennas To The Rack Cavity

    A9. Route the antennas to the rack cavity A10. Mount the remaining cavities Skip this step if you have a non-radio product. Non-radio products, which have the letters 'NR' in their Follow steps 4.2-4.5 starting on page 17 in the product identifier (PID), are delivered without antennas.

  • Page 110: A11. Fasten The Mounting Plates For The Speakers

    A11. Fasten the mounting plates for the speakers The left and right mounting plates are identical. Repeat the same procedure on both sides. 1. Hang the mounting plate on the risers. Check 2. Secure the mounting plate with one screw at that the hooks enter all slots on both sides.

  • Page 111: A12. Mount The Subwoofer Grille

    A12. Mount the subwoofer grille There is a grille in front of the subwoofer outputs. 1. Choose which center part to use: It is composed of three parts. • Use the one with a cut-out if you are going to lead the cables between the table and the video system across the floor.

  • Page 112: A13. Mount Components

    A13. Mount components A14. Connect the antennas Follow steps 6-9 starting on page 22 in the Skip this step if you have a non-radio product. main part of the installation guide to: Non-radio products, which have the letters 'NR' in their product identifier (PID), are delivered without •...

  • Page 113: A15. Connect And Organize Cables

    A15. Connect and organize cables A16. Mount the content cavity and screen mount brackets Follow steps 12-13 starting on page 29 in the main part of the installation guide to: Follow step 18 starting on page 44 in the main part of the installation guide to: •...

  • Page 114: A17. Mount And Adjust Spacers For All Screens

    A17. Mount and adjust spacers for all screens The system has six adjustable spacers, which prevents the screens from leaning on the wall panels. Place them as shown in the illustration. Spacers Spacers 1273 mm (50.1 in.) Spacers 1650 mm (65.0 in.) 1650 mm (65.0 in.) spacers 100 mm (3.94 in.)

  • Page 115: A18. Mount The Remaining Components And Grilles

    A18. Mount the remaining components and grilles Follow steps 20-26 starting on page 60 in the main part of the installation guide to: Spacers for the content screen • Mount the camera • Mount the fan duct ×2 • Mount the loudspeakers •...

  • Page 116: Connector Panels

    Connector panels The codec (Cisco Codec Pro) O P Q A. Antenna connector L. HDMI inputs with audio and video, 4Kp30 B. Line outputs (Euroblock, 3.5 mm) M. Camera input (3G-SDI / HD-SDI), 1080p60, HD-BNC, 75 Ω C. Microphone/Line inputs (Euroblock, 3.5 mm) N.
  • Page 117 The amplifier (Cisco Natural Audio Module IV) The Cisco Natural Audio Module IV is a 16 channel audio power amplifier with Ethernet and analog inputs. A. 12V power input and output. Passthrough current limited G. Analog inputs / Line inputs...

  • Page 118: More Information About Our Products

    Visit one of these websites to find out more about setup, management, and use of this product. Use the first link if your device is registered to the Cisco Webex service and the second link if the device is registered to another service.
  • Page 120 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) D15490.02 | Room Panorama Installation Guide...

Table of Contents