Makita MLT100N Instruction Manual page 14

Adjusting the bevel angle
Fig.9: 1. /RFN OHYHU 2. Arrow pointer 3. Handwheel
/RRVHQ WKH ORFN OHYHU FRXQWHUFORFNZLVH DQG WXUQ WKH
KDQGZKHHO XQWLO WKH GHVLUHG DQJOH ƒ  ƒ LV REWDLQHG
The bevel angle is indicated by the arrow pointer.
$IWHU REWDLQLQJ WKH GHVLUHG DQJOH WLJKWHQ WKH ORFN OHYHU
FORFNZLVH WR VHFXUH WKH DGMXVWPHQW
CAUTION:
After adjusting the bevel angle, be
sure to tighten the lock lever securely.
Adjusting positive stops
Fig.10: 1. ƒ$GMXVWLQJ VFUHZ 2. ƒ$GMXVWLQJ VFUHZ
Fig.11
The tool is equipped with positive stops at 90° and 45°
WR WKH WDEOH VXUIDFH 7R FKHFN DQG DGMXVW WKH SRVLWLYH
stops, proceed as follows:
Move the handwheel as far as possible by turning it.
3ODFH D WULDQJXODU UXOH RQ WKH WDEOH DQG FKHFN WR VHH
if the saw blade is at 90° or 45° to the table surface. If
the saw blade is at an angle shown in Fig. A, turn the
DGMXVWLQJ VFUHZV FORFNZLVH LI LW LV DW DQ DQJOH VKRZQ LQ
)LJ % WXUQ WKH DGMXVWLQJ VFUHZV FRXQWHUFORFNZLVH WR
DGMXVW WKH SRVLWLYH VWRSV
$IWHU DGMXVWLQJ WKH SRVLWLYH VWRSV VHW WKH VDZ EODGH DW
ƒ WR WKH WDEOH VXUIDFH 7KHQ DGMXVW WKH DUURZ SRLQWHU
so that its right edge is aligned to the 0° graduation.
Fig.12: 1. Arrow pointer
Switch action
Fig.13: 1. 21 , EXWWRQ 2. 2)) 2 EXWWRQ
3. Restart button
7R VWDUW WKH WRRO SUHVV WKH 21 , EXWWRQ
7R VWRS LW SUHVV WKH 2)) 2 EXWWRQ
Overload protection system
This tool is equipped with the overload prevention sys-
tem. The tool stops and the restart button pops up when
the tool is overloaded.
In this case, perform the following procedures to restart
the tool :
1. Press the restart button.
2. 3UHVV WKH 21 , EXWWRQ
Rip fence
Fig.14: 1. Nut 2. Rip fence 3. Screw head
If the rip fence comes close to the saw blade, change
the rip fence position. Loosen the nuts and slide the rip
fence out from the screw heads. Slide the screw head
into the groove on the short side of the rip fence and
then tighten the nuts.
When the rip fence is attached to the left side of the
saw blade, switch the rip fence position. Loosen the
nuts and lift the rip fence together with the nuts. Place
the thread of the screws into the grooves so that the rip
fence comes to the saw blade side. After that, tighten
the nuts.
Fig.15: 1. Rip fence 2. Groove 3. Nut 4. Screw head
Sub table (R)
Fig.16: 1. Screws
Fig.17: 1. 6XE WDEOH 5
7KLV WRRO LV SURYLGHG ZLWK WKH H[WHQGDEOH VXE WDEOH 5
on the right side of the main table. To extend the sub
WDEOH 5  ORRVHQ WZR VFUHZV RQ WKH ULJKW VLGH FRXQWHU-
FORFNZLVH SXOO RXW WKH WDEOH 5 IXOO\ DQG WKHQ WLJKWHQ
the two screws to secure it.
Sub table (back)
Fig.18: 1. Screws 2. 6XE WDEOH EDFN
7R XVH WKH VXE WDEOH EDFN  ORRVHQ WKH VFUHZV RQ WKH
left and right hand sides under the table and pull it out
EDFNZDUGV WR WKH GHVLUHG OHQJWK $W WKH GHVLUHG OHQJWK
tighten the screw securely.
Slide table
CAUTION:
When using the slide table, secure
work with the clamp on the miter gauge. It is safer
than using your hand and it frees both hands to oper-
ate the tool.
Fig.19: 1. Slide table 2. /RFNLQJ SODWH
CAUTION:
After using slide table, be sure to
lock it by moving the locking plate to the vertical
position.
This tool is provided with the slide table on the left side.
7KH VOLGH WDEOH VOLGHV EDFN DQG IRUWK 3LYRW WKH ORFNLQJ
SODWHV RQ WKH EDFN DQG IURQW VLGHV WR WKH KRUL]RQWDO
position before using it.
+ROG ZRUNSLHFH ¿UPO\ ZLWK WKH PLWHU JDXJH XVLQJ D
FODPS RQ WKH PLWHU JDXJH DQG VOLGH WKH ZRUNSLHFH
together with the slide table at the time of cutting
operation.
Anti-kickback pawls
WARNING:
Use the Antikickback pawls when-
ever possible during the through cutting opera-
tions. This will help prevent the material from being
SXVKHG IRUZDUG LQWR WKH RSHUDWRU GXULQJ D NLFNEDFN
VLWXDWLRQ ZKLFK PD\ UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
Fig.20: 1. $QWLNLFNEDFN SDZO 2. Clamp
7R UHPRYH WKH DQWLNLFNEDFN SDZOV IURP WKH WRRO ORRVHQ
WKH FODPS RQ WKH URRW RI WKH DQWLNLFNEDFN SDZOV DQG
then pull them out. To install, perform the removal pro-
cedure in reverse.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and unplugged before carrying out
any work on the tool.
14 ENGLISH