Cisco TelePresence SX80 Reference Manual page 37

Cisco TelePresence SX80
Contents Introduction
xConfiguration Cameras SpeakerTrack ConnectorDetection Mode
This setting applies only when a Cisco TelePresence SpeakerTrack 60 camera is connected to the
codec (video system).
Determine whether to automatically detect or manually configure which video input each individual
camera is connected to. You should choose manual configuration in situations where the codec
does not receive EDID information from the cameras. Typically, this will be when you use HDMI
repeaters that do not pass on EDID information.
Requires user role: USER
Value space: <Auto/Manual>
Auto: Automatically detect which video inputs the cameras are connected to.
Manual: Manually define which video inputs the cameras are connected to. Use the Cameras
SpeakerTrack ConnectorDetection CameraLeft and Cameras SpeakerTrack ConnectorDetection
CameraRight settings.
Example: xConfiguration Cameras SpeakerTrack ConnectorDetection Mode: Auto
xConfiguration Cameras SpeakerTrack ConnectorDetection CameraLeft
This setting applies only when a Cisco TelePresence SpeakerTrack 60 camera is connected to the
codec (video system). Furthermore, Cameras SpeakerTrack ConnectorDetection Mode must be set
to Manual.
Enter the number of the video input that SpeakerTrack 60's left camera is connected to. For
example, set to 1 if the left camera is connected to video input 1.
Requires user role: USER
Value space: <1..5>
Format: Select a valid video input number.
Example: xConfiguration Cameras SpeakerTrack ConnectorDetection CameraLeft: 1
xConfiguration Cameras SpeakerTrack ConnectorDetection CameraRight
This setting applies only when a Cisco TelePresence SpeakerTrack 60 camera is connected to the
codec (video system). Furthermore, Cameras SpeakerTrack ConnectorDetection Mode must be set
to Manual.
Enter the number of the video input that SpeakerTrack 60's right camera is connected to. For
example, set to 2 if the right camera is connected to video input 2.
Requires user role: USER
Value space: <1..5>
Format: Select a valid video input number.
Example: xConfiguration Cameras SpeakerTrack ConnectorDetection CameraRight: 2
Codec SX80 API Reference Guide TC7.3, OCTOBER 2015.
D15107.05
About the API xConfiguration xConfiguration
xConfiguration Cameras SpeakerTrack Whiteboard Mode
xConfiguration Cameras Camera [1..7] AssignedSerialNumber
37
xCommand
This setting applies only when a Cisco TelePresence SpeakerTrack 60 camera is connected to the
codec.
Determine whether to enable the Snap to Whiteboard feature or not.
The Snap to Whiteboard feature relies on a speaker track camera. When a presenter is standing
next to the whiteboard, the camera will capture both the presenter and the whiteboard if the Snap
to Whiteboard feature is enabled. If the feature is disabled, only the presenter will be captured.
The Snap to Whiteboard feature is set up from the Touch controller.
Requires user role: ADMIN
Value space: <Off/On>
Off: The Snap to Whiteboard feature is disabled.
On: The Snap to Whiteboard feature is enabled.
Example: xConfiguration Cameras SpeakerTrack Whiteboard Mode: Off
The camera ID is the number n in Camera [n]. By default, the camera ID is assigned automatically
to a camera. If EDID information is not passed on from the camera to the codec, the camera ID is
not persistent after a reboot. This means that a camera may get a new camera ID when the codec
(video system) is restarted.
You should use the Cameras Camera AssignedSerialNumber setting to cater for configurations
where the codec does not receive EDID information from multiple cameras. This setting allows you
to manually assign a camera ID to a camera by associating the camera ID with the camera's serial
number. The setting is persistent until the codec is factory reset.
Typical situations where the codec does not receive EDID information are: when you connect a
Cisco TelePresence 60 camera using 3G-SDI; when you connect a Cisco TelePresence 40 (Cisco
PrecisionHD 1080p4xS2) camera; when you use an HDMI repeater that does not pass on EDID
information.
The default value is an empty string.
Requires user role: USER
Value space: <S: 0, 20>
Format: The camera's serial number. String with a maximum of 20 characters.
Example: xConfiguration Cameras Camera 1 AssignedSerialNumber: "FTT0123456F"
API Reference Guide
xStatus Appendices
Copyright © 2015 Cisco Systems, Inc. All rights reserved.