Cisco TelePresence SX Series Installation Manual

Installation Guide for Cisco TelePresence SX20 Quick Set
SX20 Quick Set components
y SX20 Codec y Ethernet cable for LAN
y Camera options y Presentation cable:
*
A: PrecisionHD 1080p 12X - VGA to DVI-A cable, or
B: Precision 40 - HDMI to DVI-D cable
y Table Microphone 20 y Power supply and
(1 default and 1 optional) power cable
y User interface: y Codec wall mounting kit
(optional)
- TRC6 remote control with
two AAA batteries, or
y Camera mounting bracket
- Touch 10 controller (optional)
y HDMI cable for monitor y Microphone extension cable
(1 default) (optional)
y Camera cable
In addition to the SX20 Quick Set you must provide a monitor or
projector, and a loudspeaker (external or built-in to the monitor) to
complete your video conferencing system.
Documentation
https://collaborationhelp.cisco.com
https://www.cisco.com/go/sx-docs
Visit one of these web sites to find more information about the setup,
management, and use of this product. Also regulatory compliance and
safety information is included. Use the first link if your device is registered
to our cloud service, Cisco Webex; otherwise use the second link.
* You may order the product without a camera.
78-100554-03A0 | 2018 MAY | © 2018 Cisco Systems, Inc. All rights reserved.
Recommended room setup
The following should be regarded as Camera
guidelines only. Try things out on-site
Place the camera at eye height to
before fixing any mounting positions.
get the best perceived eye contact.
Explore the Cisco Project Workplace Typically, this is about 1.2 m (4 ft)
to find inspiration and guidelines when above the floor.
preparing your office or meeting room
Use the camera self view function
for video conferencing, https://www.
to make sure all participants are
cisco.com/go/projectworkplace
captured by the camera.
Aim for good illumination of a
person's face to avoid shadows. Also
avoid direct light on the monitor to
prevent reflections.
Camera options
Microphones Option A: PrecisionHD 1080p 12X
Place the microphone(s) as close to
all meeting participants as possible.
Option B: Precision 40
本产品为 A 级 ITE，在其使用说明，铭牌等显著位置中已包含如下内容的声明
(We declare here that the subject product is A class ITE product, and the
following statement is clearly marked in the user manual or nameplate):
EMC Class A declaration
此为 A 级产品。在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对干扰采取切实可行的措施。
WARNING: WARNING:
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
product may cause radio interference in which case the user may be required to take adequate measures.
required to take adequate measures.
声明所在位置 (Position of the Declaration):
Snap on the lens hood to Typical room scenario:
prevent stray light from Medium to large
meeting room.
disturbing your video
experience.
You can use the optional
70˚
camera bracket to place
the camera on top of the
monitor. Fasten the bracket
to the monitor with Velcro.
The camera snaps to the
magnets on the bracket.
You can use the optional
Typical room scenario:
camera bracket to place Medium sized
the camera on top of the meeting room.
monitor. Fasten the bracket
to the monitor with Velcro.
70˚
The camera is fastened to
the bracket with a screw.
Tool: 4 mm Allen Key (not
provided).
A 级声明 (A Class product declaration)
警告
This is a class A product. In a domestic environment this
使用说明 User Manual
