Suzuki 2006 SX4 Service Manual page 613

Scan tool data
At vehicle stop
Shift solenoid A
At 60 km/h (37.5 mile/h) constant speed, 20% or less
(CMD)
throttle opening and 3rd gear ("3" range)
At vehicle stop
Shift solenoid B
At 60 km/h (37.5 mile/h) constant speed, 20% or less
(CMD)
throttle opening and 3rd gear ("3" range)
At vehicle stop
TCC solenoid
At 80 km/h (50 mile/h) constant speed, 20% or less
(CMD)
throttle opening and 4th gear ("D" range)
At vehicle stop
Shift solenoid A
At 60 km/h (37.5 mile/h) constant speed, 20% or less
(Mon)
throttle opening and 3rd gear ("3" range)
At vehicle stop
Shift solenoid B
At 60 km/h (37.5 mile/h) constant speed, 20% or less
(Mon)
throttle opening and 3rd gear ("3" range)
At vehicle stop
TCC solenoid (Mon) At 80 km/h (50 mile/h) constant speed, 20% or less
throttle opening and 4th gear ("D" range)
Ignition switch ON and brake pedal released
Brake switch
Ignition switch ON and brake pedal depressed
MIL request Ignition switch ON
Scan Tool Data Definitions:
Input shaft revolution (RPM)
It indicates input shaft revolution computed by reference
pulses coming from input shaft speed sensor on
transmission case.
Output shaft revolution (RPM)
It indicates output shaft revolution computed by
reference pulses coming from output shaft speed sensor
on transmission case.
Battery voltage (V)
It indicates battery voltage read by TCM as analog input
signal by TCM.
ATF temperature (°C, °F)
It indicates ATF temperature detected by signal from
transmission fluid temperature sensor installed in valve
body.
Pressure control Sol (pressure control solenoid
valve) (%)
Electric current value ratio between electric current value
being outputted from TCM to solenoid and maximum
value can be outputted by TCM.
Vehicle speed (km/h, mile/h)
Vehicle speed computed by reference pulses coming
from output shaft speed sensor on transaxle case.
Gear position (P, R, N, D, 3, 2 or L)
This parameter is indicated actual gear position.
Throttle position (%)
It indicates throttle valve opening ratio sent from ECM
through CAN communication line.
Vehicle condition
Accel actual position (accelerator pedal actual
position) (%)
It indicates accelerator pedal opening ratio detected by
signal through CAN communication line fed from ECM.
Engine speed (RPM)
It indicates engine speed computed by signal through
CAN communication line fed from ECM.
Coolant temperature (engine coolant temperature)
(°C, °F)
It indicates engine coolant temperature detected by
signal through CAN communication line fed from ECM.
Cruise control signal (ON, OFF)
ON: Signal which inform that lock-up inhibit signal from
ECM is turned ON.
OFF: Signal which inform that lock-up inhibit signal from
ECM is turned OFF.
Transaxle range (P, R, N, D, 3, 2 or L)
It indicates transmission range according to transmission
range switch signal.
"3" position switch (ON, OFF)
Inputted signal from "3" position switch in select lever.
ON: Shift select lever to "3" or "2" range
OFF: Shift select lever to other above range
Shift solenoid A (COM) (command signal of shift
solenoid valve - A) (ON, OFF)
ON: ON command being outputted to shift solenoid
valve-A.
OFF: ON command not being outputted to shift solenoid
valve-A.
Automatic Transmission/Transaxle:
Normal condition / reference
5A-25
values
OFF
ON
ON
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF